Search results

On board fuel processing I am thinking along the same lines except I plan to haul much of my processed WVO and the processing equipment on a twin axle trailer. Also, I plan to carry a diesel powered generator on this same trailer with slave cable connecting a large battery pack so most...

Are you by any chance parting out some of the MEP003A's? I may be needing a generator off of one when I see the real situation with mine. Another screwing by GL. They switched on me and wouldn't make it good. Thanks, Orren

On my truck, M36A3C, the rubber connector faces to the center of truck; might be worth a try? Also, please let me know a good place to get a fuel sending unit replacement. Good luck.

Insurance Who is your carrier and for what vehicle? Thanks, Orren

M36a2c Need the date of manufacture, etc. M36A2C w/w NSN 2320000771619 VIN 032710499 Date of manufacture: ???? Manufacturer: ??????? Purchased from private individual in MN. No markings on bumpers. Thank you for your help, Orren Winjum

Since you have some cables, do you have two prong slave cables or just the two prong male and female connectors? Also, could use a 12 prong male trailer connector. Also, looking for at least 5 'L' brackets used to hold the battery and tool boxes up. Light rust OK but no cracks or pits...

Slide in camper I bet there's a lot of you guys that would like some sort of camper that could bolt in the M35 or better yet a M36 like mine. Using four hard points and a properly located tree limb it could be lefted enough to clear truck bed. I have been studying the Alaskan Camper design...

Bait and switch by GL and FBI case GL pulled a bait and switch on me with a MEP 003a diesel generator. I have filed a internet fraud case with the FBI. Lets see what happens. If nothing ,then the rot is very deep in our federal government. I may need your storys, so keep the evidence...

I live in Florida and was told we can not get antique tags for large trucks such as the duece. Good luck and let us know what happened. Orren

GL bait and switch Be careful. GL pulled a bait and switch on me when I got a MEP 003a. For some reason I wondered why they don't identify this equipment with the serial number; know I think I know. If you pick it up they want to stick you with it even it you can prove they did not give...

11:00 x 20 NDT Are the 11:00 x 20 NDT's the same diameter as the 9:00's ? Would like to use 11:00's on the front only if possible. Thanks, Orren

WVO for fuel I use waste vegatable oil mixed with 10% diesel. First, I run the raw oil through 5 micron bag filters after straining out the coarse stuff. Then I run it through a centrifuge that brings it down to less than 1 micron. This runs great in my 2500 RAM but I'm in North...

M36A2C available Please have your friend contact me. My M36A2C w/w is loaded.

The rubber end cap does nothing but cover the adjustment screw/nut. I had to replace the whole thing but you might get lucky and just be able to clean it inside. Note: I had to reorder mine twice before I got a new one that worked. Typical for the junk put out these days. You could try a...

I have available the two complete stock box seats from my M36A2. Let me know if interested. Thanks, Orren

Why????? Quiet duece is an oxymoron: That big pipe in the air is what it's all about. No appreciation for the greater things in life it looks like to me. Besides wait until you go offroad in a nasty place and you can kiss that undercarriage pipe goodby. There's a lot of ways to quiet...

LED lights Where do you get these varible voltage rate LED's? I think this is the best way to go for me to change out my trailer's bulbs. Thanks, Orren

My M36A2C w/w, dropside, made in 1960 by Kaiser Jeep, VIN 0327-10489. Good luck with the study, Orren

Can we use the same wheels on the 1100's as are on the 900's? Also, where is a good place to get 1100's? I just need two for the front only; going to keep the duals, as is, on the back. Thanks, Orren

I have a reconditioned M36A2C W/W, long wheelbase for sale with many extras. Let me know if you are interested. I'm located just east of Tallahassee, FL if you would like to come take a look. Thanks, Orren