Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.
It looks like the common glue for this job type is HH-66. My plan is to attempt the repair. I also realized a previous owner cut a hole for a rear door. I'll have to either find damaged cover that has the rear panel in tact or just fill it in with some new sheet.
I got a cover when I purchased my Deuce. I am trying to decide if it is worth repairing.
The main thing I noticed is it appears to be taller than standard. A previous owner appears to have drilled holes to hold the side supports up higher to accommodate the tall cover.
Anyone know if this is...
Engine is up and running again.
I'm more surprised how well it ran with poorly functioning injectors than how it is running now.
It is at least as good now, but there is no obvious improvement.
This video shows the exhaust around 4:40 and it is very clean...
I have Hagerty in MN and was not informed of any garage requirement when I signed up. I was out of options and was happy to find any legal means to drive my Deuce even if the policy covered nothing but allowed me to drive. You should ask "how about if my garage fits in my Deuce? Would that...
It's running again:
Part 5: https://rumble.com/vj41wv-m35a2-cylinder-liner-repair-part-5-running-again.html
The new liner and the 5 cracked liners have survived about 70 miles of driving so far.
from the TM:
"
1. Look at left side of crankcase opposite each cylinder bore about one
inch below top of crankcase. The letter "Y" opposite a cylinder bore means
this is a Y-size cylinder bore. The letter "Z" opposite a cylinder bore means
this is a Z-size cylinder bore."
In the picture...
I have found multiple sources for type "Z" cylinder liners, but my Continental LDT 456-1D has the "Y" stamps.
Though a Z fits, I don't know if it will work as it is slightly smaller OD.
Are the "Y" types extinct?
I use a simple breaker bar, did the math, and put a piece of tape where all my body weight at that point creates the correct torque.
As others said, the condition, cleanliness and lubrication is a factor.
I have a torque multiplier, but don't use it unless a nut is stuck, which is rare.
I found a rebuild kit for the "D" turbo that included bearings, but not the compressor wheel. There were also a lot of compressor wheels, but it was hard to be sure if any were a good match and I ended up getting a used 'D' turbo as a replacement.
Here is the kit (note it may NOT work for a C...
Thanks for the reply and info. I had no luck finding non-brass fittings so took the chance. I wore a full face shield for the initial testing. The tester is a very common, below $100, just search for 'diesel injector tester'. Surprisingly the main body of the tester is plastic, but it still...
While working on another repair, I decided to test my injectors and discovered half of them were not performing well, yet the vehicle had been running fairly well. Started easy in warm weather, not great in cold weather.
Video showing my fittings setup to work with a cheap ebay tester and...
So far I don't know why the liner failed but 2 possible contributers:
1. Previous turbo failure where compressor wheel got ground up by nut that fell off and bounced around. This allowed small aluminum particles to get sucked into the air intake...
2. Injectors not functioning well. Some ok...
Yes, it is a great piece of art. One of a kind.
UPDATE 4-10-2021: I got a NOS cylinder liner kit that included a piston, piston pin, rings pre-installed, and even the piston cooling nozzle oil jet assembly.
Piston has what looks and feels like some sort of black coating:
Wanted...
Part 3: Manifolds, head, piston and liner remains removed and inspection:
https://rumble.com/vf69lr-m35a2-noise.-cylinder-liner-broken-part-3.html
So far the damaged parts are:
Piston
Cylinder liner
Oil jet thing
Gaskets
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!