Search results

For those who haven't been following the 5TTR/M939 ESP thread, it is intertwined with the development of the MTVR concept. I felt there's enough merit to have a separate thread in order to keep information organized as more is discovered. 5TTR/M929 ESP Tread...

I'm selling one of my A1 M-Gators with the diesel Yanmar engine. 508 hours. This is a clean unit and has been fully serviced. Electric tilt bed, folding bed sides, battery disconnect, new tires, new seats, and much more. $12,500. Pick up in Dallas. I have more photos and video if requested.

I have a few new in crate combination heater/AC units for military S shelters: S-250, S-280, etc. AIR CONDITIONER, VERTICAL, COMPACT, 18,000 BTU/HR 208 VOLT, 3 PHASE, 400 HERTZ NSN 4120-01-127-0716 $250/ea. They need to go SS express, freight, or local pick up.

Looking for a good running non-turbo 6.5L diesel engine out of a HMMWV, preferably an A2 model with the serpentine belt.

I was skimming an old military vehicle publication circa 1997 and found an interesting truck. It appears there was consideration to remanufacture the 5 ton trucks like they did the M35A2 -> M35A3 ESP (Extended Service Program). The blurb says it has the same Cat 3116 and Allison 1545 as the...

I recently acquired a 98' M1078 with the WTECIII. It has an issue which I believe is focused on the transfer case (mechanically). The truck will start and go into gear, both Drive and Reverse, but it will not move. The transmission engages appropriately and puts a load on the engine but the...

Looking for a member close by that could put some batteries in a deuce and see if she fires up. I just need it running enough to drive on a trailer.

Looking for the TM's for the M878A1 "yard dog", "yard mule", "shifter", etc Number Title TM 9-2320-285-10 Operators Manual for Truck Tractor, Yard-Type, 43,500 LB GVW, DED, 4x2, Army Model M878A1 TM 9-2320-285-24-1 Organizational, Direct Support and General Support Maintenance...

I've been watching the HMMWV auctions close for anomalies and gabbed this unique "M1097R2" recently. CTIS, winch, pintle extension, and more. I've had a few AD friends look at it but so far no cohesive conclusion on what role or loadout it had while in service. ADA launcher, satellite erection...

I have an M757 I've been slowly restoring and came across two more tractors near me. They're in fair to rough shape but at least rolling chassis with major components left in place. For anyone needing a parts truck contact me and I can get you in touch with the owner. I really don't want to see...

Is anyone in Oklahoma City with a deuce/5 ton and towbar that could lend a hand? I have an M816 (without cab) that needs to be pulled out of a parking spot so it can be winched onto an RGN. The area is too tight for the trucker to get to it.

Looking for a physical or digital copy of the TM 9-2320-230-34P for the M656, M757, M791 5 ton 8x8 Trucks. I've searched high and low to find all manuals for this series of truck and lack this one. I've only found two physical copies on ebay but $75 is a bit much.

I've read the TM's and covered the dozen or so related SS thread regarding fuel prime on these M35A3 trucks but I fear my issue has surpassed the TM troubleshooting steps and into deeper water. This M35A3 fired up momentarily when I first cranked her. She turns over quick. She does fire on...

Looking for a copy of the -20 for troubleshooting. Unfortunately I've only found the following which is limited to operator 2 step diagnosis. ---------------------------------------- LO 10-3930-664-12 Model MHE-270 NSN 3930-01-330-8907 model MHE-271 3930-01-330-8906 Truck forklift ded...

Looking for someone local to do some basic PMCS to get the truck running to drive up onto a trailer. Will compensate for materials and time. Let me know.

**This thread may continue to develop as facts and documentation are discovered.** I had the fortune of unknowingly recovering 2 prototype MTVs this past week from a location not too far from the old Stewart & Stevenson plant in Sealy, Texas. I'm doing the due diligence of documenting the...

I've had many FMTVs but this is the first I've had with this numbering on the door like this. It was covered up (poorly) with tan paint and flaked off with the power washer. I'm positive this unit was overseas due to gunring support & platform, IFF panel mounts, etc. Anyone have insight?

My "new to me" M10A will be here in a few days and want to see who else owns a unit out there? Anyone have any info on these units that's useful/interesting?

Would someone post photos of their deep water exhaust setup, mount, and bolts. I was lucky/unlucky enough to get a NOS exhaust pipe but it doesn't mate up to my M1123. The part number comes up at M1097A1 but doesn't fit right. Did they change the exhaust for the "A2" generation? Bracket and...

For those who haven't heard I've come into possession of a Buffalo MRAP trainer built on an M925A2 chassis. I want this thread to document the unique nature of this machine and updates as I work on it (even if slowly). I felt this should go under the "Heavy Armor" category due to the extensive...