Search results

Did anybody else attempt to contact Diesel Dave about the FAV? That was the instructions in his 2 youtube vlogs, so as to not burden the museum owner with dozens of emails from tire kickers, he said to contact him about specific items.

I can't believe I never posted internal photos. The side wall thickness is 0.1715" Corner bosses are 0.654" radius from the exterior corner radii. Hardware 4each 1/4"-28 x 3/4" overall countersink machine screws. In order to use your CAD to make burnable string patterns for lost...

Dataplates.net is out of Missoula Montana, I've never met the man in person. The T-Shirt launcher idea was to be for a Mardi Gras Parade, local, that did not happen due to the Chinese-lab created with training by USA scientists Covid 19 virus. Concept is sound. Use a heat shrink tube to...

That looks gosh-darned good! What does the back side of the main housing look like? Did you print in bosses for drilling/tapping to screw on the base plate?

Hello, has anybody turned up a rebuild kit for the late A2/REV/ECV separate type Power Steering Pump? Either the 107 or 120 Bar type 6500522 NSN 2350-01-554-4731, it should be a package of 3 or 4 O rings, one nylon ring and a bearing.

Craig, were you able to tell if your flywheel was lightened? Re: Engine Cases-I spoke with a former CB Performance employee back then (CB used to be Claude's Buggies). CB was one of the companies that sold Don Hatz the parts he used to build up engine cases. The VW Engine Number list on...

I use this self-adhesive closed cell 5mm foam for another purpose (Special Forces GMV IED Kevlar Seat anti-squeak). When applied to your fuel cell along the V support bracket area at the B Pillar it can help eliminate the annoying squeaks: CJ5 Jim still has the remnant of a similar foam...

Can somebody please give me the dimensions for the exterior face plate for the FAV Engine Protection System? I am trying to have the face plates made again, at a minimum; the entire functional EPS circuit board if possible. I am talking to a couple different electronics people about the tech...

On the Schneider page for the cam they state the results were with 1.1 ration rockers.

My un-installed Driver Side rear seat bucket is not pre drilled for installation pop rivets. The truck bodies were pre-assembled by type before setting on the chassis. The blind rivets are installed on the crew compartment side of the tub. I wouldn't think the trans tunnel would be prefilled...

Hello, I bought a Chenowth 4LWC Fast Attack Vehicle, rolling chassis not running, that I need picked up in Minden, NV near Lake Tahoe, transported to FL Panhandle, Navarre FL. Also has a 2nd set of wheels and a large box of parts. Chassis is listed as 1600lbs, probably another...

I forgot to ask if the FAV rockers were standard geometry?

9th Infantry Division FAV #0014 has emerged, Chenowth Chassis 4LWC 1592, so far the 2nd lowest number known to still exist behind Mogman's #0010. Important stuff is intact, especially the rear anti-sway bar system. She is going to need side bins, radio shelf, wedge fuel cell, air log...

In the parade the FAV has a weapons mount installed on top, I can't tell if it is original or copy yet. It is tough to see with the piece of camo net there but it looks like it has the bolt lug welded to the square tubing side, for the clamp. Guess we have to find somebody who lives close...

Did you just blank off the old engine protection system subpanel until reliable copies turn up?

The DWF Sensor Cup was originally installed on the body by the frame in the A Pillar area. The installation of the armor upgrades over the GWOT necessitated the cup be relocated to by the front differential... That narrow bracket between the brake guards is the 2nd different variation...

As a reference, the original Modification Work Order Kit the military issued to replace those 1st gen seats with the Highbacks, 57K0290, you can find in the TM section. It will show you what had to be air chiseled off the driver position, and how the footwell was modified with 2 aluminum...

If your friend is a Veteran he can order direct from Interco in LA and get a military discount.

Roger this pic was in the magazine article you posted in the 9th ID Facebook Group. Looks like aluminum blocks clamped around the rear frame tubes with a flat bar connecting both sides, that supported the stowage shelf overtop the engine bay. Is that an Empi air filter box over the carb...

The two pcs of aluminum tubing with the ends squished flat are for the tunnel insulation panels. The long silver/bare aluminum strip closes the tunnel side of the seat boxes. The installation would have another sheetmetal flange about 4-5 inches long for the seat bucket to the rocker panel...