Search results

Has anybody had any experience with the Tacom branded replacement gauges? I’m in need of a fuel gauge. I just ordered a NOS oil pressure gauge, but not sure how long that will last. Some of the NOS gauges seem to be problematic from what I’ve read. Thanks

I will be painting my deuce with Behr paint soon. The bed and the cab have Carc on them. They will require minor sanding and priming in small areas. However I will have to sandblast my hard top. Also I have an unpainted NOS outer windshield frame that is raw steel. Once I sandblast and epoxy...

I’m looking for someone that can crawl under their truck and take a few pics of their transmission lines that run to the transmission cooler. I pulled the transmission and I don’t think I have them routed correctly. I think the top line is the one in question. One of them is hitting the pto...

I’m looking for a cross reference part number to replace my coolant surge tank cap. Thanks

I have to replace my rear main seal on my 925a2. I have gone to the Cummins website and typed in my engine serial number. I see the part numbers for the seal and the gasket for the rear main seal housing. What I haven’t found on the Cummins site or looking in the TMs is the gasket that goes...

I keep searching the manuals and they go dark then my iPhone goes back to home screen. I’m looking for the yoke that slides onto the winch shaft that is held on with the shear pin. Any help would be appreciated. Thank you

I’ve searched with no success. Does anybody know good part numbers for longer wheel studs for the deuce? Thank you

Deuce Bed from Newberry, Florida to Emporia, Virginia Near I-95 or elsewhere I may need a deuce bed moved from Newberry, Florida to Virginia near the city of emporia. That's the city that I-95 and route 58 meet. I actually live in Chesapeake, Virginia near Virginia Beach. We have property 20...

I'm looking for some suggestions hopefully by some experienced carc paint and primer painters. I picked up this NOS cab and it has a few spots of peeling paint. Upon my research, this is the water based carc with the white chromate and lead free primer. From what I have read, it's not the best...

I would like to know what the lmtv frame width is? I also would like to know what the inside and outside bed dimensions are. Also looking for some pics of how the bed mounts to the frame and some pics of rear of the truck. Thank you

I'll be heading to the Aberdeen Rally in May. My plans are to pull my 20ft trailer with my longbed truck. I will be empty headed North but my plans are to buy a few things and bring them back home. As of right now my plans are to travel north on the Eastern Shore then Deleware to Aberdeen. If...

Anybody going to Kublos Surplus located in Brackney, Pa that is also going to the Aberdeen Rally? I need a deuce fender and door picked up a brought to rally. Thanks

Is there a clamp that secures the engine shut off cable to the firewall or somewhere else? If so what does it look like? My cable pulls out about 5 inches before engine cuts off. Thanks

Does anybody know who sells the trunnion seals? Also just asking, what about the trunnion bushings? Thanks

Does anybody have a formula on what colors and quantity to mix rustoleum paint together to get the green our trucks are? I'm looking to just paint frame and axles for now.

I have U Bolts off. Torque rods are pulled. Does this bolt need to be removed also? I can't budge it.

I'm looking for advice on how to handle this situation. I have rust coming from the area where the stake pockets are. Between where the stake pockets are welded to bed. Thought about cutting off stake pockets, repairing rust, then having new pockets fabricated. Then possible riveting them on and...

just like the title states. Yes I know what Rtv is 😀 Thanks

Just like the title says. If I cut the U Bolts to change upper torque rods in deuce, how much is a replacement set? Also I remember years back napa having a stubby socket for the top rod nuts. Really not interested in grinding socket to make it fit. Just don't want to regret cutting them off...

I bought my deuce back in 2003 from govliquidation.com. At the time starting bids were about $100. I've been away from the hobby awhile. I would occasionally look on govliquidation.com for trucks. Noticed they disappeared on that sight. So my question is what has changed over the years? Is...