Search results

I am trying to find a good fuel tank for my multi tractor. I need the drivers side tank with the larger fuel pump hole in it. If it had a working fuel pump that would even be better. :-D

Well I was settling in today and the phone rang.. Darn kids these days think there deuce will go anywhere.. I think with tire chains he could have made it but I pulled him out and all was well again.. I might have to go back tomorrow and show him what some XL's can do! :-D Darn load restrictions...

I am looking for a 1 3/8 x 10 spline 11 inch clutch and matching 8 bolt 11" pressure plate for my M37 Canadian truck. Anybody have one for sale? Or maybe know some part numbers for NAPA?

Anybody traveling north from or through the Janeville Wisconsin area? I am looking to get a off road trailer hauled closer to the UP of Michigan / Wisconsin border or just closer to the Tip of Mitt of the lower peninsula. It will need to be put on a flatbed trailer. See pictures attached. :-D

Hi guys, I am trying to replace a broken wheel stud on my deuce. I didnt realize there were so many ones.. Anybody have the part numbers or the specs for both the left and right hand threaded studs? Help!!!:-D

Is this the carburator for a 5 ton gasser?

I sold a 5 ton winch to some friends of mine and it will be mounted on a tug boat using hydrolics to run it. This winch was off a 900 series so it has the coupler and hyrolic motor flange.. 1 1/4 shaft size is what he said. So far a civi size motor has not been found. Do any of you have the...

Well guys while setting off to fab up some long awaited winch bumperettes for my Canadian M37 I learned that the drivers side is a 1 1/2 longer than the passenger side.. Never noticed this before and just wanted to share.. I almost made a booboo.. Thank goodness I measured both sides of my R2...

A friend on here has a WWII jeep. Here is what the main data plate says from what I can make out. It is a Ford data plate and not brass It has these numbers stamped in it. 158878 11-5 48 It has another stamped alluminum plate on the middle of the dash It is stamped 5536949 20-10-48 The...

A local friend from my town purchased a M35A2 in the last Michigan auction at Selfridge air base. He is new to the deuce and is looking to have it hauled. The weather could be bad and its not worth the hassle. Anybody get one from the same auction that needs it to go north? You could share...

Which jeep is this for? Anybody recognize the numbers? I am not a jeep guy. M38 maybe?

Ok radio heads.. I stumbled accross a RT-70A/GRC radio.. Whats the propper application for it? Jeep? M37? Both? What power unit and mount does it take if it would be correct for a M42 command car? Any pictures of a complete set up? I believe it to be M series correct. I was looking for a RT66/67...

I am in the market for the 4 belt pulley that goes on the 100 amp generator for my M42 , 230 engine.. I have the pulley for the water pump and the crank. The one on the generator is wrong. I could also use some info on how the water pump pulley works with the fan? Thank you..

Hi guys.. I obtained a fording kit for my M37 but no directions..:| Anybody have kit on there truck that can post some pictures of the valve arangement? And the bracket hook up on the back of the truck? Or maybe the instructions for the kit?

It is very cold outside and no work other than plow some snow so why not work on some old Spitfire 265's, 251's and 230's... :-D Took some pictures for you guys to enjoy. Saving what I can from the scrapper and putting a 230 and a 251 together for a couple projects. Also tearing down another 251...

Where can I find a rebuild kit for the LU 4 Braden winch found on M37's, M715's and some others? Wanting all seals, bearings, worm gear the works..

not sure if this will work.. How do you post a Youtube or website location now?

Hi guys. I am looking for a good used, or rebuilt NP 420 transmission for my M37 Canadian truck in or around the state of Michigan. Anybody have one they will part with? I have given up trying to find a PTO for the ACME trans and must have a winch on the truck. I would like the newer style NP...

Anybody have a good used or new one they will sell.. I am in need of one more for a storage trailer I picked up.. M105 size..

Anybody going to Fort Carson Colorodo that is willing to pick up a pallet of MBU heaters and ship them to me in Michigan for a fee? I am not having any luck with the GL reccomended shippers? Or maybe someone is coming East?