Search results

Also the place where the neutral and ground are tied together is also where the solid copper wire for pole and panel is attached. Can I attach the ground and neutral together here? And I should have the bonding strap on Genny disconnected with this setup correct?

My Xm381 needs an upgraded horn to go with the Truck. What type of horns have you guys used and how did you plumb them in? Train horns etc. Thanks Sent from my moto z3 using Tapatalk

Got the correct CO2 extinguisher for my 802A. I think. Sent from my moto z3 using Tapatalk

I was wondering if anyone had a link to the correct fire extinguisher that will fit in this holder on my M45A2? Sent from my moto z3 using Tapatalk

The little glass fuse in holder behind main guage panel. Mine was burned out when aquired. Is this for battery charging and should it be a 6A 32V 311 glass fuse or should the A be higher? I also have the 24volt pulse charger from military on mine. Can it stay hooked up when gen is running or...

Is it Completely asbestos and has anyone put new insulation in one ask mine is separating and falling on generator. Mainly the top peice is coming off. Sent from my moto z3 using Tapatalk

I bought an mep 002a recently. I was wondering, should it fluctuate in output? Not wildly. I will get it warmed up and then set it. My htz will jump up or way down when left alone. Not all the time, but randomly. Also the other day I cranked it up and engine sounded awesome ran great, but...

Replace gears or clean up pieces and change oil and run? Sent from my moto z3 using Tapatalk

What in the world? This looks nothing like my TM. Is there supposed to be a bearing behind clutch plate as in TM? And this is clutch disk that was in it and holy cow does this mean I need a new flywheel as well? Deep cracking. Crap. Anyone got a spare? Sent from my moto z3 using Tapatalk

Would it hurt an M105 bed too much structurally to cut out this portion of the bed? A 900 series tire hoist will fit right between the pillers placed on the bed itself. Any thoughts? Need a spare out here and my bed. Thirty Mile drive just to get to town and back home. Any Ideas are...

I was under my truck and noticed I can grab my front drive shaft and turn it quite a bit side to side. I also changed the oil in the front diff and noticed metal shards on the magnetic plug. Can I use the chunk out of a rear axle if needed? Need a thread if there is one for checking the...

Any picks of the military rifle mounts in a deuce cab? I have a M151/A1/A2 rifle mount kit for my Bobber and want to see what others did. Thanks Sent from my moto z3 using Tapatalk

So with a 002a I have a spare gen set for parts and someone put a single spin on fuel filter and water separator. Is this a good deal? Or stick with the old tried and true? Also are these guys multifuel as well. The plate discusses using different grades of deisel and JP4. Fuel? Sent from my...

Who has a compressor wrench for sale Ive seen several older threads but can't find people or link no work. Sent from my moto z3 using Tapatalk

I have looked all over the place. Anyone know where to get these rubber isolators or something that works? Sent from my moto z3 using Tapatalk

I read on a post here about using tubeless tires on A2 rims without tubes. Just need some sort of rubber insert? Anyone got info on this? Or a link to post. Thanks Sent from my moto z3 using Tapatalk

When I run my M35A2 for a while and warms up, it sounds great then it just sort of dies and won't start for a while. It's like the fuel pump can't keep up and then I let the pump run for a while it will start back up and run. Have fuel pressure but it seems low. Any help or thoughts would be...

My brake booster was changed from long style to short style and when this was done there is a small vent tube coming out of the top of the brake cap. It goes into a larger line that goes up to the air pressure regulator but the line was crimped and not connected to anything. Is the fuel tank...

Could this be Wet Stacking or can a leaking flame heater leaking into elbow do this. The oil coming out smells like deisel but is super thick like old oil. Truck has sat for 11-12 years. Haven't run it much. Thoughts? Thanks Sent from my XT1585 using Tapatalk

If I put 14.00-20's on my M54, can I use standard combat rims on front or will I need Hemmit wheels in front to keep from rubbing on turns? Sent from my XT1585 using Tapatalk