Search results

I really appreciate the help from the info on this thread. I am going to try to strip the take out axle of it's A3 bearings. I want to keep them as spares for my A3. Yup, found them. Thanks, I want to keep the A3 bearings as spares for my A3. I would definitely use the A2 conversion bearings...

Thanks a ton for this thread!!:smile: I have a take-out rear A3 axle from another's bob project. I had intended to strip it of it's A3 bearings, seals etc. Can the hub be removed from the axle with out destroying the seal? Is the outer bearing outer race and the inner bearing outer race a...

I have a take-out rear A3 axle from another's bob project. I had intended to strip it of it's A3 bearings, seals etc. So from what your post says, it is a bad idea due to destroying a seal. What seal is it? Can the hub be removed from the axle with out destroying the seal? Is the outer bearing...

I would love to have this truck.:mrgreen: I would put higher lift springs on it to install rebuilt rockwells, enough lift to level out the drive shafts, sitting in my garage under it,:jumpin: a c30 chassis steering box for cross steering in it, m35A3 rims and tires under it, that I also have...

Good to hear you are proceeding with the service.:grin: Maybe 2 x on the engine oil change.:idea: For the tranny here is some good reading: http://www.steelsoldiers.com/deuce/66399-m35a3-transmision-question.html?highlight=transmission+flush+dexron...

SUper NICE Truck :grin: I bet the air pump is crimmped off cause there is not and alternative configuration for the serpentine belt. If you get the truck, get the wiring manual and get familiar with it so you can trace the circuits. :popcorn:

30-45 psi is about right for a warmed up engine in the 1200-1500 range. I think you have too much fluid in your engine crankcase. Water and oil are not a good mix in an engine! ouch:?

I know you are going to want to read this thread: http://www.steelsoldiers.com/deuce/74278-m35a3-rear-wheel-bearing-packing-photos.html Those axles, transfer case, tranny, engine, steering box, are gonna want service. Warm metal and cold water, those assembles will suck water like a vacuum...

Here's a good thread for you to read about M35A3 wheel bearings:http://www.steelsoldiers.com/deuce/74278-m35a3-rear-wheel-bearing-packing-photos.html Hope this helps!

Read this Thread, It talks of your wheel issues: http://www.steelsoldiers.com/forum-news/86376-if-you-cant-delete-you-dont-need.html I had a serious cracked line on the left front wheel. It took 10xs as long to inflate the wheels but it would not cause the wheel to deflate. I will subscribe...

How is it going over there? I am going to look for all the nuts and bolts and the bracket and cover for the generator. I'd like to keep it with the truck. How did the alternator charge on the trip over. I bet I don't run the truck at speed enough. Does any one know if the front hubs will alow...

Will a functioning CTIS keep water out of the Hubs and wheel bearings by virtue of the pressure top inflate the tires? If you do deep water fording how do you keep water out of the axles center housing, transfer case and the transmission? Will a low presure air cicuit (1-5 psi) do this...

YIPPEEE, now I get to title and license My green camo near mint rustree M1008 with good ole poop slingin, hog tyin farm plates, (I live on a farm) or I could've put on regular truck plates!! YAY!!!!!!:jumpin::mrgreen: License and title a 67 bug. 65 Mustang.......... :eek: Now if the...

It'''s going to cost a whole bunch of money to do my M35A3 PM (fluid changes, tranny flush...) I see that as a resposibility to myself and the public to do everything I can to make sure I have a safe operable vehicle. I understand the law of lugnuts, what is expected of me while I operated all...

WOW, Splendid job! Beeeuuttiiifull Wheels!!:smile: Your posts where a great read and an excellent contribution to the thread!8)

How much for safe, strong design specs for a wheel like I described in a previous post? Thanks Dennis

A shout out to Fragnaboo Fragnaboo Can your pressure cast the wheels I descriobed in a previous post and machine them for $500-$700 each?:jumpin:

Dear Santa Claus, I want for Christmas New 6 hole aluminum 6 slotted wheels .... Dear Santa Claus, I want for Christmas New 6 hole aluminum 6 slotted wheels for my M35A3. They should look like old keystones or cragers. I want them with the same offset as the original wheels. I want them...

Dear Santa Claus, I want for Christmas New 6 hole aluminum 6 slotted wheels for my M35A3. They shouold look like old keystones or cragers. I ant them with the same offset as the original wheels. I want them with a deep drop center in the rim between the beads so I can mount them with soapy...

I woneder if a functioning CTIS will keep the water out of the hubs and wheel bearings?:jumpin: Will a 1-5 psi air circuit from a fording kit hurt the tranny? Blow fluid past the seals and starve it for fluid??:cookoo: Do the axles, transfer case and the tranny with a fording kit, will it...