Search results

@swiss other than above questions.... any hints on getting End Piece installed. Just laying on the ground that piece of material (triangle) at the top above the Garage Door material has my brain twisted like a Pretzel. Can't make heads or tails of it when End Piece is laid out flat on the...

was reviewing the TM's and just realized what you meant by this answer. Is there enough flex in the material if Walls/Roof section (WRS)* is across the frame whole, and hanging down on both sides, and w/ Evave pins and Ridge Pin grommets all set in place? Curious if you think in that...

answering my own question... yes the fold down. When frame arches are assembled they do not fold down tight. They stick out some horizontally. They hit a stop point in direction of Peak/Ridge Beam. Stop is at Vertical. Hmmm.... As to what they do when tarp in place... guess they are not...

@swiss orr?? The pin on the Eaves that the Tarp goes on (12ft height? approx). How do those function?... pivoting wise.. Trying to picture in my head this.. seems they fold down.. but that makes no sense..... then they would not help support hanging walls... but then again maybe they are...

PS- Its also been raining... so took that time to improv (I think) the video on preping the site. Little less sucky now. Nver said knew what was doing. Let me know on youtube if it is better with the tweaks (some music, shortened intro) , if music picked helps/hurts. etc. etc. Thankx.

Well... can't find a welder who can anytime soon mount a winch to my cherry picker soooo have to go to a modified plan. Do have a different sucky winch that has portable mounts. Will use that hanging off the end of the C.Picker hook. Adds complexity but gotta do what gotta do. It has cable...

videos out: sad attempts at humor ... https://www.youtube.com/playlist?list=PLByDKgq-6sYosCVk1EA3RuMZdKecthyFX

sneak peak Operation: no Purple Pill LME-E (Light Maintenance Enclosure- Erection) Goes live 15min from this post publish (8:15pm) PS- May Marine Corps have many more honorable years forward of its Birthday Today. Enjoy your Marine Corps Ball those who served and thank you. Oorah.

Szgt. Myselv has set for a video to fall around 15:00hrs 11/10/24 aprox. 30 min. from this posting

hmmm..... didn't consider the exhaust vents in lower walls cause they are lower than the flu output on heater..... but wonder if stuffed a small galvanized trash can into one with interior covered in insulation .... ran the stove pipe to that along with an exhaust fan in the path... hmmm...

Heater. Acquired a 1950's? coleman drip diesel heater (non military). Uses same carburetor/fuel regulator as the old military ones. Also plan to drip waste oil into the same burner pot to extend burn time per dollar. The flue pipe comes out the back of the Coleman. Any ideas on where should...

lighting plan in place and purchased . some of it delivered. LED stuff replacement end wall arrived. Waiting on a welder so can add 3ton winch to cherry picker. hmm.. what else... plan as of this moment is - cross of previous plan but bundled close to what @swiss did Tarp rolled up...

for manual valve in a tilt cab.... mount it on a plate X"xY" large.. cut hole in floor of cab.. that is that minus a bit... but not minus so much the valves dont fit thru hole in cab floor. Put a seal on the plate that squashes as the cab closes. then again you have to accommodate for...

2003 is between versions I think. .. and around the time I think the manuals became embedded inside branching diagnostic software. The pdf-ish manual the software used is not classified. BUT... The software is not readily available to public though so it is very difficult to get to it...

much appreciate. Murphy... 2 hours

It's all unpacked so what's your bets? is wall/roof tarp: Pretty good, Usable, Minor Repair, complete :poop:.......... :carnac: Jumped on an Ebay solution just now to replace the end piece. Was vewy vewy painful. Tit over 500 smackaroos. Guess it is still a win.. got the whole LME...

When Losing Becomes Winning / It's All Perspective. Losing- As reported- One end cover tarp-- badly torn.. Losing- Maximum-ish 500 bucks to fix/ Minimum around 350 bucks?? Winning- Very first bundle of tarps unpacked had this in it..... giving time to start looking Winning- 2 options found and...

Does an end need to go on before the roof/wall roll installed?

well on second thought maybe. Remember; crane. (Cherry Picker) situation here is working from UNDER the frame and not the outside of it and anything that has to be reached, must be reachable from roof of box or cab without moving truck, till the tarp is holding itself up (and Cherry Picker...

So hook the Eaves pins in first (first pins before peak)? Then go for the peak ones.... that would reduce wind issues... had batted that option around. Friends helping.... been trying for that for various things for 4 years and offered barter, pay, etc... total fail. Must be...