Search results

As stated above, the 105 is the proper trailer for the M35. It has an empty weight of 2700 pounds, has the same rims and tires as the M35 and has air brakes that hook up to the M35. They are great behind a M35 and honestly, too big for even a modern 1 ton civilian truck. The M101 has an...

The plug is at the end of both pigtails. Just out of the picture. It is kind of funny this came back up. The old volt meter would hover in the lower half of the green. I swapped it out because in the summer when the glow plugs don't work very hard. The needle would stay just above the...

double post, sorry.

A frame mounted receiver hitch and the weight you mention should work just fine. As long as you are not in a hurry and plan ahead for braking. Many people have done similar sized loads with no issue. However, if you plan to do it often. Add a transmission cooler to help the TH400 live long...

Are you sure it is getting into 3rd gear above 35 mph? Driving nicely to 55 and then maintaining 55 should give you 20 plus mpg if everything is working right. Parking brake stuck on?

The kits available are for an entire rebuild. The -20 walks you through the entire process and it is pretty easy to do. I would suggest doing everything so you know for sure you didn't miss something. You do have the long style older one, right? That is the version the kits are for. I...

The stock master is easily rebuilt with cheap parts. Replacement stock masters are pretty cheap as well. However, if you are going to be doing anything besides shows, parades and just driving slow on weekends. I would suggest a dual line master as mentioned in the thread George linked to...

I am also running 10 11.00-20 tires on my 1952 REO Gasser. I will have to go look at my data plate on the dash, but I think any octane gasoline down to 75 or so will work. Anything you run without ethanol is a great idea. Don't worry about the octane basically. With the stock 5 speed non...

I also daily drive a 6.2 powered CUCV. So does my wife. However, I work on them a good bit and did extensive electrical, brake and fuel system work before putting them into service. Without a back up vehicle of some kind, I would suggest something newer.

It seems that if the pitman arm didn't get changed out, what else did not get done? I would suggest you read through the CUCV forum and you will find dozens of threads asking the same question as you.

I think it would depend on the size of your slide shaft. I do realize the ones that will be swollen are probably #5 and #7 which means you can't do much. That situation I think needs the real tool or maybe a vice grip to let a pry bar grab onto. My back up idea to the one used was to take a...

The air tools don't really help much in this case. Only about half the manifold bolts aren't studs with injector lines, fuel lines or something like that on them that need to be moved out of the way. Then of course, none of the IP mounts, injection lines or timing gear fasteners can be done...

There are several glow plug removal tools on the market. Searching through thread about this subject also brings up some home made solutions. One thing all methods have in common is that they don't always work. Sometimes the plugs do break off and the injector has to be removed so the pieces...

Brake theory time. Fluid pushed by the master cylinder piston moves pistons in each wheel cylinder. The master can only push so much fluid per push of the pedal. The pistons in each wheel cylinder are pushed back by the brake shoe springs. If you have a large gap between the shoes and the...

A few people fully remove all the injection lines to get the pump out. That is not needed though. Follow the directions in the -20 and it will take 2-4 hours. Most of that time difference is getting the 3 bolts for the gear out and back in. If you have somebody to turn the crank while you...

Going back to original question since we can argue about how much starting fluid it takes to launch a 6.2 head into space forever. Yes, if it is hot enough outside and you have really strong batteries and a starter that turns the engine over really, really fast. A 6.2 can be started cold with...

As pointed out in this thread, there are two basic ways to use the can for engine running. Cut a hole for the starter or move the rear cross member back. I moved mine back and just put in longer bolts with some nuts as spacers. Either way works great.

A few things I have learned that might help others. If you don't have anything besides an engine hoist to pick up the can, you can't put it on the ground. The hoist legs are in the way. Jack stands at the outter corners of the stand will allow most engine hoist to roll out from underneath...

You are supposed to have about 2" of pedal travel before you get any pressure build up. If you are getting more, then you probably need to adjust your brake shoes. The -20 manual calls it a "minor adjustment and it is real easy. Jack up an axle, spin a tire and using an 11/16" wrench on the...

Solid state flasher box or the older style? If solid state, I will send you the best in my opinion wiring diagram for knowing which pin goes to what wire on systems with the solid state box and newer arm.