Search results

I have the 210-34-2-1, 2-2, 210-34P, etc. but non of these manuals actually states including the -1D engine. All of the manuals except the -34P are 03April81 and the 34P is May 1974. I'm assuming that the -1D was added after 1981 but it is really unusal that they did not update the manuals, or...

I took my front driveshaft off yesterday due to the non-airshift transfercase, removed the front drive hubs, removed the left forward axle shaft, and temporarily installed front drive hub on rear. Drove it about a mile down the paved road and back for a test. What a difference in handling! I...

I purchased my muffler from NAPA today (and intake elbow). My muffler box had been opened and was taped shut. The muffler was o.k. (never installed) but there were no directions inside and the box is not marked with directions either. I know that this sounds silly but there is a In and an Out...

In my '68 M35A2 WO/W there is a switch on the instrument panel that I can not identify. I have not turned it on with power on due to concerned about it's function. I have looked through the -10 and have identified two other switches that are installed in the other plugged hoes on some trucks but...

Does anyone own a 68, 69, or 70 M35A2 made by Kaiser-Jeep that could e-mail me a pciture of the Data Plate that the serial number or VIN is stamped or engraved into? I need to purchase a new data plate to replace my crappy generic plate installed during rebuild and I want to get the right one...

What are the correct tools needed to check the remove the oil fill plugs in the transmission, transfer case, and axles? Is it 3/8 or 1/2 square female drive perhaps? Just want to make sure I have the right tools and I could not find this in the stickies on this site or in the L.O. or TMs...

I have not seen one of these before and have not read about anyone receiving one of these. It is a form letter starting off with "You were assessed to purchase / receive surplus Department of Defense property through the DRMO or its commercial partner". "Some of this property on the US...

Does anyone have the dimensions on the opening cut in the roof for the gunner to operate his weapon thru when mounted on the Ring Mount? (It is approximately 2 feet according to pictures) I need to make a Steel Closure or Patch Panel and need the thickness of the top material and the...

I read back 30 pages and thought that I had seen a notice by somone having MWO kits for older towbars. My main legs are 41.5 inches long (tube portion only) and are 2.250 inches in outside diameter. I want to intall the MWO collars and was wondering inf any has done this by civy parts or if the...

For a first timer since G.L. was in play, I have a question. After the EUC is cleared through Battle Creek, how long does it take to get invoiced and once the invoice is paid, how long and where do yiou get the bill of sale? The reason that I ask is that I can not get a transit plate (paper tag)...

Does anyone know approximately how much a non-dropside bed weighes? I need to remove my bed for a few days to do some work on the rear lower cab area and re-paint too. I can drive the truck out from underneath the bed but not sure if I have the "right stuff" for the job. Thanks, Jim

I found a TM for sale. 9-2320-209-35. Described as "Depot Level" for our trucks but the older version dated June 1965. I thought that the 209-34 was Depot level but it seems to be missing some information too. 209-34 doesn't seem to be the in-depth level that a contractor or Government...

Does anyone know what the average wait time is once a EUC is cleared? I was curious to see how much longer it may be now that my form has passed the screeners and it going north to Michigan. Thanks, Jim

I understand the socket for the front hub nuts is 3 inch. Anyone have a a line on the socket designed for this? I know that SnapOn and Mac have it but don't need it that bad. There should be a manufacturer for the thin wall ones similar for use with the older M38 and CJ series jeeps. Thanks...

Hello fellow MVers. I was reviewing my digital copy of TM9-2320-209-32-2-2. The manual was downloaded from LOGSA a year or so ago. Paper page number 17-638 is missing. It skips from 17-637 to 17-639. The other missing page is 17-648. It skips from 17-647 to 17-649 and there is two identical...

Could someone tell me what the thread size is on the front and back axles regarding the wheel studs? Can rear axle studs be put in the front hubs without machining the hubs? Thanks, Jim jimm1009@yahoo.com

Does anyone have the size of the square shaft for the exterior door handle? Is it 5/16 or perhaps 3/8 square stock? Approximately how far does it stick out of the handle? Thanks in advance. Jim in Louisiana jimm1009@yahoo.com

The key code for the U.S. CUCV is 73Y2 as delivered from the factory. This is the B-key or commonly called the Trunk Key (rounded edges). If your truck was loaned to another agency, they may have changed the locks but probably/ usually not. A sure way to know is to pull one of the door...

I will be picking up my first M35A2 in a month or so. Have been reading and watching this list and G503 too. Would it be prudent to remove the front drive hubs and rear axles shafts and install temporary hub covers or covers without shafts for flat towing? I do want locking front hubs but don't...