Search results

I bin trying to figure out the same thing for my self, but I only need 2 boosters. the s10 seat was my first idea. I have seen seats for sail that move back and forth more than the 1088 do.(wife can be crammed lol) so a small bench if I can find one, mite fit behind passenger seat.

from floor to top of plate when level its 63" but that's with 395/85r20 tires, so it could be lower if you get smaller tires for it. haven't got title yet but did some hill climbing up a dirt pile that I cant even walk up if I wanted 20 ft high and had no problem truck rocks!!!!!!

yes when I get to work tomorrow ill measure it and let you know if Suprman don't beat me to it. I do know it sit higher than our 2000 mack tractor, would have to use tire inflation to lower tires to get under low bed trailer hock up.

just hooked up two my regular batteries for now and it worked noticed that there is a small P on positive wire terminal and a N on neutral so picture and new find works like a charm. THANKS SO MUCH

thanks, cant find any thing I want on tm's this will help. hope I can get a cheaper battery but probably not since there square. only use deka batters at my work.

thanks I just read some thing that said 12/24V on them, so I guess that's whats going on. just need to find a picture on whats what. I tried looking at wires to figure it out but still no clue since 2 off of alt. go to a box with more wires then to battery, figure its a regulator. any one know...

they do make batteries that fit in these gens mep002,003,802,and 803 I have them all lol will look tomorrow when I get to work on what the make and numbers are I have put in them and battery hold down from parts store fits fine.

picture on box only shows 2 jumper wires and 2 wires to truck +- didn't help with the other two wires I still have left over. and picture shows 24V wiring. no help on the 12v way I have it to start it. hopping I don't burn anything up with way I have it!!!!!!

I just got a m1088, but was missing all the batteries. it has 4 wires coming from truck and 2 from jump start cylinder.(total 6) if I hook them up like you would think, all 24V way it does nothing. but if I hook one of the wires on 12V way it starts rite up, iam so lost(nothing like my m925) if...

Yes I did try to flash it, with my house outlet. Hope that doesn't mater only one time did the lights flash but still no electric. i even tried putting 12 volts to the two terminals on A2 board like TM's says, still nothing

PS... I got it from GL at a New York DOT garage. they helped my load it and told me it worked just fine when they put it in corner of fence 5 yrs ago ��

I have beat my head against the wall with the TM's and still am lost. my mep003 will get 20-30 volts as you start to crank it over only the first time in a day, then it just flat lines same with Hz. ( readings from outlet on my hand held gauge) i have replaced the voltage regulator board and the...

Before replacing them try taking them apart and cleaning up the piston inside like the older mep002,003 so far I have cleaned 4 that didn't work and every one started working just fine. Guess they all dried up fuel and just got stuck to hard for the magnet to move them up and down.

so update on my broken down mep-002 so my friend/generator guy, put a good/used rheostat and (A2) regulator that he got from one of you nice people and still the same problem aua if any one has any idea at all please HELP and or any place in PA near north of philly that knows what there doing...

P.S. any 1 know what the batterys are, in TM numbers come up as a starter at napa. the MEP802a i got didnt have any batters in it or any of the ones i looked at when i picked my gen up.

Great help, thanks. I just got one the mep802a myself yesterday and looked in all the TM's, i couldnt find oil filter numbers or any thing to do with the onan engine. My luck missing couple little parts like air filter cover and fuel shutoff bolts. :(

thanks gave it to a friend that knows about generators and electric way more than i do. think ill stick to working on trucks and engines more lol

found a 1970 m35a2 w/w on ebay in maryland rite now for $4990 already titled buy now. cheap from what i bin seeing. just got my self a 1984 m925 refurb. 2010 with only 1k miles on it fron ohio nice 1 month 1 week till i get it titled i hope 1 of 12 images Enlarge

ok kinda new at this, i got a mep002 and was missing some diods on the a2 board/voltage regulater. voltage stuck at 90 volts. i also had a parts mep002 i got with it so i swithed the board. now the voltage keeps going from 90 to 140 +- when i plug anything into it voltage drops to almost...