Search results

I was 52D (91D now), but attached to Motorpool so most time was spent on trucks. 62A..... Just went through the Hospice experience with my mom. Hats off to your sir! I can't imagine the things you have seen. Thank you for what you do. The high pinion appears to just be a different third member...

And not even any good reason for it! The truck runs! Idiots the lot of them..... But also they don't give a fast flying fart about breaking Uncle Sam's discarded trash and know they will never be accountable to the buyer so....... Assume NOTHING..... I would be so nervous leaving all this in the...

https://www.govplanet.com/for-sale/Light-Medium-Tactical-Vehicle-%28LMTV%29-2006-Stewart-%26-Stevenson-M1079A1-LMTV-4x4-Van-Truck-Hawaii/12800456/NSN/2320-01-447-4938 That one I assume. Driveshafts are properly F'd..... AND that's a low pinion truck. Don't let them drive it till new...

The JUNK I worked on for the Hawaiian National Guard was so rusted I certainly wouldn't want to own it. Only place I have trained where we were ROUTINELY changing HMMWV hydraulic brake hard lines. Even with the silicone brake fluid they were rotting out. Had a couple trash cans FULL of rusted...

No pressure at the test port either means the solenoid is bad or it's not being activated correctly. (Or you really don't have pressure but since the truck drives that seems unlikely). The small movement you are seeing could be the "peak" from the peak and hold PWM signal from the TCU and the...

No...... I *bought* one for $160 (free shipping!) off ebay! You have to be watching for those deals..... Here's one - this seller usually accepts make offers I've noticed: https://www.ebay.com/itm/322568821025

Mine was worse - punched a hole in a piston. Ebay, surplus channels and surplus truck/parts dealers, Napa, FleetPride, etc. I got a good used compressor for $160 on ebay and rebuilt the head and then rebuilt my original head to carry for a spare. It's all off-the-shelf Haldex parts. These...

There's already a thread going about that compressor issue and others. They eat exhaust valves at a furious rate: https://www.steelsoldiers.com/threads/who-are-the-experts-on-the-air-compressor.220678/ That's the head that you have a hole in. And that compressor is toast. You need a...

Probably THE two biggest pieces of advice for a new FMTV owner: 1. Good batteries - charge and test individually/disconnected from the truck. 2. Clean every ground, and all the major power distribution points. Then CHECK the voltage drop from the from battery negative to chassis grounds, cab...

Yep - that's how I was instructed to test them in school - late 90's US Army Power Generation Systems - we still had a lot of 15/30/60k generators with mechanical injection. Manual lever pump and a graduated cylinder.

Correct. My 2008 doesn't have the newest one either - our serial numbers are too low. But always check the serial number to make sure the military didn't swap out the transmission or something.

You're grave-digging. Not likely to get any reply to a thread from 5 years ago. And in any case the availability and best option shifts regularly depending on when you ask and what's available. There's tons of information out there about alternator alternatives. It depends on which engine you...

Agreed. 15-20 seconds is nothing. My 2008 C7 will roll coal under load when cold. The 370 HP map might have a little to do with it, but yeah - when REALLY cold they will smoke on startup. Remember these are non-emissions engines so there's no DPF, and on your 3116 there's no catalytic...

Have considered that also. Just too busy and don't need that many.

It is the same part exactly. It requires no modifications. I've installed them as well as just using the diaphragm out of them. I'm assuming the part number difference is materials, coatings, components suppliers, etc. Or it might just be that the government version has a different part number...

IDK where the actual f*** you fellas are buying these for $200 - $250, but they are $79 (including shipping): https://www.finditparts.com/products/8710926/haldex-314013005 🙄 🤷‍♂️ And sure the non-adjustable is still cheaper - but you are talking about using two.... so now were down to $30 and...

Yeah but they never cared enough to redesign it.... 1993 to 2021 are all the same damn loose fitting latch. It's willful at this point when it's not been addressed for 28 years. Lowest bidder designed it. Another lowest bidder manufactured it..... and lets face it - the lowest common...

No. Not a design flaw. "Lowest Bidder" is the answer to your question. I installed a BRAND NEW one out of the package and it was still exactly like this. There are no slots on the box or the latch and the rivets fit the holes tightly. That's just the way they made them.

You probably don't have it if you don't have the fuel lines to connect to the van. Mine was also missing. I used a 24v Facet military pump to lift fuel up into the heater tank and then the diesel heater has it's own dosing pump that is gravity fed from the heater fuel tank.

Yeah I was thinking that also but it's not easy to remove. You could likely bend it without removing it.