Search results

I will need to refresh myself on that then, I always though it was for what I said above. Yes, you did good here friend! Once it's fully serviced, load her up good & let it eat!! Get a few of the spade butt connectors. They all seem to let go at the senders in the engine bay but it's super...

I have found that the Facet, square pump is said to fail here on the form more often simply because they are on older manufacture generators. I have had about the same fail rate on the AirTex. It really doesn't matter what pump you have, if it is run dry for to long or has a bunch of gummed up...

With all the wetstacking that thing has in the pictures, I don't think it was run hard. The fuse mod is for when the unit was run at lower RPM than it should be and the voltage regulator is making up for that to keep voltage proper & it burns things up. The fuse mod should be done but unless you...

A lot of the stuff I have gotten via GSA programs still has these kinds of documents in it. Have though about e-mailing POC's with my official e-mail to get details if needed, but haven't had to for anything yet.

This seems to be exactly what mine did in this video series..... head gasket was bad. It eventually kept getting worse & ate all the coolant & blew the engine.

This thread troubleshoots the half reading issue; https://www.steelsoldiers.com/threads/mep-802a-m8-percent-load-gauge-issue.212356/

Here's what you should do to test your generator.

You'd think with all the over done stuff on these units, the'd have had put something on those unused mounting holes as guides or holders for that cable.....

I soak with Super Clean first, then spray with a hose. Do it a few times. No need to use a pressure washer as the Super Clean breaks up most anything grimy. If needed, get a brush or something. With just a hose, usually you don't need to worry about electrical, but it's a rule of thumb to never...

I check for 12v on the body harness side. Confirmed wiring is good all along it. Also from the switch to the TCM connector itself. I used a multimeter to adjust it and make sure it opens/closes with a slight pedal touch right at the TCM connector (Not J1, at the actual purple connector) so I...

Well, it is plugged in, brand new, tested good, and everything I can tell so far the wires are good. Two TCMs that are new tried as well. So it more than likely is not the sensor itself, but something messing up the signal coming from it. There is no light with the J1 disconnected and power so...

Tested the wires today. From J1 to h for the Engine Speed Sensor tested good, p didn't give me continuity but looking at the wire diagram, it is shared with the Throttle Position Sensor and then grounds in the transmission itself ultimately..... I think? When you have a bunch of shared...

This may be helpful. The injection pumps can be annoying to remove/install but on an MEP 803A there is MUCH more room! I'm betting that someone already messed with them & installed them improperly. Have seen it quite a few times. Hopefully that rail isn't bent! Usually you can make it move no...

I think I need a few parts from a MEP 501A control box. If you are interested in selling, let me know.

While you have it apart, soak in ATF for 24 hours or so. :)

Injection pump replaced & truck is running. The new Crank Position Sensor didn't do the trick. Will double check the wires between TCM and the sensor. Thinking it's just the TCM at this point. If the wires above test okay, going to install another new one & hope for the best!

I know nothing about this specific setup, but one think I learned about military communications setups.... just because it is the same connector, does not mean it is the same pin out. Unless you can 100% confirm it is the EXACT pin out.... just because it fits, doesn't mean it won't turn...

Funny, once you know, how the stuff starts popping out. Maybe it was for putting the Jerry can handles through? :p

The smoke is more than likely what you suspect... oil & fuel built up in the muffler. Along with anything else over it's time that may be burning off. I would run it at 50% load for one hour & then 100% for 6 hours to fully test it. Make sure it ramps up & down as it should first & adjust the...

Sorry, I must have missed that when reading. Sure looked like a pump issue. I'd replace the China injection pump as soon as you can. They are TERRIBLE. You may get 50 or so hours before it grenades. They don't properly harden the internals. Genuine Yanmar ones seldom go bad.... odd to see one...