Search results

Thank you in advance. XM820E2 Make and Year unknown. a. Serial Number (VIN number) -----C12910297 b. Registration Number ----- 05B68271 c. NSN without dashes ----- 23200509010 d. Where you bought it ----- GL Auction Camp Shelby, MS e. Bumper numbers if you can legibly read them- MS-155-106...

What about a M931 or M932 and a variety of trailers. The issue would be a CDL since it is required in KALIFORNIA, I believe. I was going to do that but don't want to mess with CDL requirement.

I can see the idea of interchanging the different boxes and beds if you only owned 1 or 2 trucks. But Why would you need to go through all the trouble of doing all the mods if you have enough trucks to have variety with the trucks intact. I am just giving my opinion. Not telling you what to...

Use the battery terminal clamps that are used on the M35 and 5 ton trucks. You can get cables made at any welding supply places. I have done that for my custom cables on the 5 ton truck. All they have to do is crimp on the proper connectors on the end of the cables for you. You can get...

I did some calculations to determine if my micro switch settings were correct. What I determined is: Since my RPM readings are a little high and the micro switches are set for the highest pulses per revolution there is no way to lower the displayed RPM by choosing a lower Pulses per RPM -since...

Today was a nice day out so I decided to start working on the Tachometer hookup. I set up some wires with a 5 amp fuse in-line and attached it to the 12 volt battery. I tapped into the single thin brown wire coming from the driver's side alternator. Hooked it tot he spade terminals on the...

What a shame! Looks like someone ruined your new paint job.

Don't you hate it when they leave you hanging in the middle of a project?

Did you try to tighten the screws on the end to see if it would stop the air leak?

The U- shaped tubes are the exhaust vents. They are supposed to be that way. Check to see if they are venting. Use the manual lever to sweep the wipers back and forth. I took the air hose off and sprayed WD-40 into the tube. I then used the manual sweep handle to work the wiper back and...

There are about 3 or 4 different diameter lines. Some are only 4" to 6" long. We took all the vacuum lines off and took them to Advanced Auto Parts to size up. It cost me less than $20 for all the hoses and the modulator valve combined. The Modulator valve was only about $12.

Yaye I got it right!

I am glad i was able to return a favor for someone who has been a good friend and helped me out in the past. I am glad the rims made it there so quickly.

When was the last time you replaced the vacuum hoses. Mine was doing that until I replaced the vacuum hoses and modulator valve. Maybe the low temperatures caused the hoses to crack.

Moderator: Can you use the word assistance needed instead of HELP for this thread? I just want to know for future reference.

I need to call them tomorrow to see what the ORD kit will cost me. The Summit kit had the shocks and Pittman arm included.

I found this info on Summit Racing when I was searching or a lift kit for the K30 truck. http://www.summitracing.com/parts/exp-k1059/applications/year/1983/make/chevrolet/model/k30/engine-size/6-2l-379/amount-of-lift-rear/4-000-in It will lift 4" front and rear. Anyone use this kit? I am...

Cold in April in Louisiana?! Any weekend is fine by me so far.

I ordered the ethylene foam panels this weekend so I can sound insulate the back of the cab as well as the floor. Since it is a closed cell foam it will not absorb any water that could rust the metal. I plan to use polyurethane construction adhesive to glue the panels to the back walls. Not...

Glad you are back safe. Thank you for your service. I look forward to seeing your project progress.