Search results

I bet you have found this web page as it has a very good set of pictures of the M151A1 with the MRC-108 equipment setup. We did not have the trailers as we were not a fixed operating outfit. I do not know how the radio equipment got installed but it looked very much like a factory install...

This should just about answer all your questions. USAF MRC-108 Communications Jeep

The 65Kxxxx markings were the Air Force assigned vehicle identification registration and were not the vehicles VIN. The VIN numbers were on the data plate and on the frame. Both the M38A1 and M151A1 and later M151A2 units were used in VN. Also there were AN/MRC-108 equipped Dodge crew cab...

The radio gear was a AN/MRC-108. The radio maint. van for the equipment was a AN/GRC-32. At FT. Benning in 64-65 we had 2 M38A1 jeeps with that gear in them. Same equipment exactly as the M151A1s had in them at that time. In July 65 we did get a M151A1 equiped unit. I was the NCO in charge...

Nice to see you in the hills area. Retired AF (1984) also. If you need some manuals and a lot of other stuff give me a shout. I have a Strata blue M35 at this time in the pole barn and way to much other stuff. Need to send some of it down the road. I do not read the general posts often so...

Just got off of the phone with Clinto. Come and get the truck Jim, Clinto said he has to much stuff on his shovel at this time. So anytime you want to pick it up is fine with me. Will see if I can get Vic to be there also as he has the heavy equipment that might be needed to load the truck...

Got to looking at this old thread today. Since I started this thread I have done 3 more "Last truck I am going to do" projects. A Marine M37, An AF blue M35a2, and a Marine M931A2. The 1957 Utica Bend and its new running REO engine is sitting in the storage area pretty much untouched...

Jim if you want the 1957 M35 just come up and get it. I will probably never get to it. As you know it is totally without any rust. It would look good in the new PB. I still have that running gasser REO engine in the pole barn. So it should take very little to get it going.

In the 1960s while working for HP Loveland division as a electronic tech I was in charge of the final electronic testing group that did the final test of the HP 428B clip on amp meter. It is an old unit but I still see them for sale on the net. It is just what is needed to troubleshoot a...

Did I read some where early in this thread that you were not going to go "Crazy" with this restoration? Hummm Does that mean this time unlike the M37 project you will not replace every bolt with a new grade eight, fine thread like you did with the M37? Must be a family related affliction ...

I did a set in 2003. I had a large pile of seats for CUCVs and used the hardware to fabricate the needed metal. I had to extend the legs as the sides on the 105 are a bit higher than the deuce or CUCV sides are are. The wood I had made of oak using a deuce seat board as a sample. Here are...

The trip to the vets parade on the 11th did not happen for the blue truck. On Sunday the 10th at 10pm local the state, county etc. all pulled their plows off of the road. As it rained, froze then dumped 6-8 inches of snow on all the roads between Custer and Rapid City. As we all know the NDT...

Got the tower signals decal Friday and here is a pic of one mounted on the truck. As mentioned it is not exactly like the one that Jeff posted (the correct one) but was the best I could come up with using my limited skills cutting/pasting/etc. of stuff already on the net. PB tried to send a...

Thanks Jeff for the picture. I will put my decal at the same location when it comes. Let me know if you want a decal for your AF truck when they come. Also let me know in a PM your mail address.

Will get one out to you when they arrive. Good job on the jeep. I have long wondered where the two we had at the Benning TACP in 64-65 went. Both M38A1s were procured off of a Marine contract and were VC-104 outfitted. (with MRC 108 type radios etc.). One was Strata blue and the other was...

Gave up on trying to find a tower signal sticker so designed one that sort of looks like I remember them. Should have them from the decal outfit in a couple of weeks or so. The cost was about ZIP so no charge PB. Send me a PM with your mailing addy. PB let me know if you want a couple for...

Thanks for checking

Pretty much done with the truck. Have to add the remote brake fluid reservoir yet, new seat covers, and de-splined front axel hubs. As you can see the troop seats are on the truck. Firmed up that the truck will be in the Rapid City parade on veterans day the 11th of November. It will be...

I found that also Jim. It is close but it refers to aircraft and the old one did not mention aircraft only vehicles. I will see if I can find the old one if not I will have to use that one or either forget the decal. Thanks for the info however. I will be talking to a guy at Ellsworth AFB on...

Does anyone know where I can get the older decal that was used on most all trucks in the 50-60s that had runway access. It sort of looked like the one pictured below. I have found on the net the current information for the one used today but it is different. The current one has a lot of...