Search results

weight of 9x20 tire and wheel

how toreplace brake and clutch bumper pads

In manual 9-2320-209-10 the cooling capacity for the LDT 465 is listed at 28-32 qts. Why the range? Recon Dutchess county, NY

what is the correct length wiper blades for the m35a2? I have looked through the forum and couldn't find a consensus. I tried finding the length in the tms but length was not mentioned. Recon Dutchess county, ny

I need to replace the temp sending unit on my m35. I've been putting PB buster on the fitting. Anything else I can do to ease getting the old unit out? I've found a lot on testing temp sending units and temp gauges but nothing on torque for installing sending unit. Should a sealent be used...

Here are more pictures from the Ropkey MV show. I hope!

A few more vehicle pictures from the Ropkey MV show.

Saw this and other vehicles at the Ropkey Armor museum outside Kokomo, Ind. recon

I have a '71 kaiser m35. About a year ago or so I put an AVM lockout hub on the front rear axle. Just recently I took the Deuce out for a drive after sitting for a month. The axle was in 2x mode. After 30 miles I was putting it away but I could not get the hub to move into 4x4 or 2 x. The...

I finally installed a winch on my 1971 M35. It was pretty much straight forward. Getting the knockout for the pto shifter out was a pain. It would not knock out. I had to drill a bunch of holes and use a chisel. The pto went on easily once I got the correct studs. Every thing else went...

I now have all the parts to install a winch on my m35a2 wo/w. I can see where the opening in the floor is supposed to go for the pto control lever. Is it a true knockout or do I need to cut it out? Any suggestions to make that opening? Thanks in advance Recon

The winch I am going to put on my M-35 is not a garwood. The plate on the pto reads "TMC Transmission Division Wolverhampton, England. " The winch plate reads "manufacturer TMC". Does anyone have any info about this pto and winch? Recon 1971 Kaiser M-35 wo/w for now

Is there a list anywhere on the site that gives civilian equivalents for military lubricants? At the end of LO 9-2320-209-12-1, for example, there are 6 different lubrications listed but I have no idea what they would be in the civilian world. It lists general uses such as chain lube oil...

I'm putting a winch on a non-winch Deuce and found a post that said 80w-90 gear oil should be used to fill the transmission and the oil should be yellow metal compatible. Can someone tell me what "yellow metal" is? How can I tell if the oil is compatible?

I have an m35a2 wo/w. Anyone have an opinion on which would be the better way to go - lockout hubs on the front or lockout hub and axle change in the rear? I have tried removing the rearmost drive shaft and it improves the steering but it is a pain to take off and put back on. Would having a...

I just finished changing fuel filters on my Deuce and all went well, no leaks. However, as I tightened the bleeder valve the head snapped off. Any place to get the valve or is it a standard valve I can get at NAPA?? Recon

Any suggestions on where to buy ndcc 9x20 tires for deuce in NY or PA area? recon Dutchess county, NY

I was in Anchorage recently and saw these trucks at a place that has the highest concentration of float planes in the country.They use the trucks to move the planes around. Recon Dutchess County, NY

Can someone tell me if a winch and all its parts from a 1953 Reo 6x6 can be put on a 1970 Kaiser M35a2? recon Dutchess County, NY

Went to a mv rally, swap meet in Hancock, NY. and found all kinds of stuff there. No rally but lots of stuff from barrels of diesel, 5 gallon cans of paint, trailers, jeep bodies (willys on the side of the hood),boarding ladders,( I bought one for my deuce), military solvents, tires and more...