Search results

Just picked up a 936A2 wrecker but don't have TM for rear winch and boom operation... I looked thru the TM section, but did not see any info on wreckers. Anyone have any info or potential sources for operations info ??

I have a duece and 101a3 + 105 trailers. I want to pull the 101 with my Dodge Ram pickup. Does anyone have a Bulb chart for changing the 24 voly signal / stop lights and marker lights to 12 volt bulbs Thanks for the help

my M35a2 has a master cylinder with vent line going to the axle tubes... can I discinnect this and attach the vent line 90 degree connector to a brake fluid reservior in the engine compartment?? Do you REALLY need the vent line.... Some master cylinders come without a hookup for vent lines...

Anyone know of a replacement part for the transfer case solenoid on a 923 A2.. alternitive part number of sourse for new or rebuilts would be greatly appreciated

I posted a "Parts Wanted" ad for a set of 5 ton bows and hardware.. Got a couple of good replies and some helpful suggestions from guys on the board.. I got an offer for the complete parts set from Digger09 in NJ. after a few pm's.. we spoke on the phone (very nice guy to converse with)...

I am installing a keyed battery switch for my 923... 4 wire go into the switch.. but I cant tell how to divide them ... to a 2 poled caterpillar switch.. looks like wire # 569 comes in from the battery to the battery switch... 81 and 81A go back to starter and 459 goes to the electrical...

Anyone ever put a bedliner in a 5 ton.. rather than just paint..??? Do it your self or commercial Any experience with lineX... I have it in my pickup, and it seems to have held up well... but this is a different story

I dont even know where to begin to look for this... is there a switch or button that releases or holds air in the system and transfers it to m105 trailer... except attaching the glanhands... Just got my M105 and my diesel mechanic friend said "all trucks have a botton or switch that sends...

I have look at all of the TM's that looked appropriate.. but I can not seem to find the gear ratio of the winch PTO for the M35 front mounted winch.. Anyone know the answer or where I can find it.. Thanks

Where is the best place to put the "Solarizer" panel. Can it be exterior or does it have to be

I am looking at an M109A4 ... what is the difference between A3 and A4... I know the A4 has the Cummins diesel and allison automatic transmission... Does it have POWER STEERING ??? any other differences ??? And what should a relatively newly referberd on go for ??? Thanks for the help..

I am replacing my main battery on / off switch wiith a keyed switch... there are 4 wires running into it but I can not make out the wire numbers.... does anyone know which 2 wire they are and their positions (as you face switch... upper left...upper right...lower left...lower right ...

Anyone have any experience with GL recomended transproters... They seem a bit on the expensive side... but I dont have any prior experience. I want to move a 5 ton 923 /925 from Ft Know to Buffalo NY... $450 to haul off base and $3.10 per mile ???

Sorry for the very basic question... BUT... can someone tell me what excatly "flipping the hubs" means for a duece... and do I need to do front and reads to run supersingle tires...??

Anyone with experience running 1400 x20 tires on a duece. I just got my goodyear 1400's mounted on Marsh wheels for Boyce... Anyone have any issue with, or have to make major modifications to the front axles to keep a decent turning radius without have the tires rub on something ???? What if...

I have 5 1400 x 20'sthat I need to get on to Marsh 1 piece rims..... any suggestions... it seems almost impossible by hand... What is the trick to doing this.. (I know the bar and big hammer part)

Permission to come aboard. !! I have been reading for a while and thought I would check in.. Just picked up a bobbed duece from Clark international 12/2/11. It is a great truck already.. but have even better things envisioned. Great threads here on the trucks, mods and maintainace. I hope...