Search results

I would have to agree that if you ran it that long, losing that much oil, and now it won't go into forward gear, then you cooked it, so your now looking at a replacement or rebuild. I tend to agree with the other member,cost wise i would look for a good pull out being sold by another S.S.member...

M35A2-AZ you sir are correct, no low range in reverse, there is even a warning placard mounted on the dash of the M939 series of trucks, stating do not use reverse while the transfer case is in low range.

Just as an FYI, but you can still buy new original paper maintenance and parts manuals for the M939 series of trucks from Portrayal press. I just got all the parts and maintenance manuals from them for my truck,were talking alot of manuals, when you stack them one on top of the other it makes a...

These shoes your talking about with the lose rivits, were they a factory OEM part, or were they a replacement aftermarket part? If they were an OEM part can you list the cage or manufacturer number stamped into them.

I have a M925A0 and i need to rotate my tires so i was looking in my tech manual 9-2320-272-20-2 dated 10-1985 and it list the lug nut torque as 450 to 500 foot pounds for the M925A0 and A1. Now for the problem, i crossed checked the lug nut torque against the latest tech manuals and came...

nadroj, on the 3 lever light switch, you have to hold the one lever on the lower right side up while you move the top center lever switch to the on position. After turning on these switches you will now have power to your turn signals. Oh one more VERY important point, if you don't turn on your...

steelypip,since you seem to know alot about this ship, is this for our blue water navy, or is this one of those inter coastal waters defense ships?

You need to read the TM's about post fording maintenance, they have lots of maintenance items you need to attend to after driving through water as deep as you have gone through.

I'd call ahead and ask Jeff if at least one of the trucks still has it's BII kit in it, if they don't have the kit you'll need to pick up a jack, lug wrench and a chain fall to get the spare tire off the back of the truck. Remember the super single tires weight right around 500 pounds each, not...

Machinist75,i am sorry to say i can't answer your question, when i left my last employer, they were closing down the whole plant, they were kind enough to give me two complete O ring kits. These two kits are made up of both Viton and EPDM O rings, and cover both thick and thin cross sections...

otrafxp, i could be wrong, but i think all the operator manuals regardless of when it was updated will have the weight data in them that your looking for.

Thanks Tow4, i took your advice and took it apart on the truck. I cleaned and polished all the brass parts, replaced the 3 O rings, lubed all O rings and bore with Parker O ring lube, reassembled it, it now works great. Oh one more thing, some of the photos i have seen of other actuators taken...

Lonnie, if you look at the photos in post #18 in this thread, you will see that i did add the jack screw adjustment just like you ask about.

UPDATE: Well i just got back from a 100 mile test drive and so far the idler is working great. Now time and miles will be the real proof if this pulley is a help or not, but i do have to say i did notice a difference today. Today out side temps were right around 80, i took the truck for a drive...

The best advice is go look at the truck you want to bid on, and if you can't do that then have a S.S. member who lives close by go look at it for you. Doing it this way will give you some piece of mind before you bid.

What's the reason why you need the older versions of the TM's?

dogbone, that's the funny thing about the web, i find a web site on pulleys that says my design in the right place, and you come back and say its not. I think at this point the only thing you and i are gong to agree on, is that we disagree, and leave it at that.

Doghead, after doing some research on the drive side and the slack side of the belts it looks like you were mistaken. I do have the idler mounted on the slack side. Please see diagram. looking from the front of the engine, D1 in the diagram being the water pump and D2 being the fuel pump and...

I took my M925 for a test drive today, when i got back i noticed a big air leak. After stopping the engine the secondary air gauge was losing pressure fast. Upon opening the hood i found air leaking out of the front of the fan drive clutch actuator. So can i take the actuator apart and rebuild...

Tow4, thanks for the complement, i have been doing custom machine work for most of my adult life, it kind of helps having a complete machine shop at your home.