• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Search results

  1. F

    FLU419 SEE HMMH HME Owners group

    Also found another use for the mog one of my boys got a 4 point (i told him 6 or bigger) still in velvet with his crossbow on the youth hunt weekend. He claimed it looked like a 6 but got a little excited. Dropped it in its tracks.
  2. F

    FLU419 SEE HMMH HME Owners group

    Finally got the mog fixed up enough for its first project (170ft trench for 100amp service to new barn) ran it with no problems til dark then turned on the rear flood lights only to have them burn out within 10min of each other. Picked these up at the Kenworth dealer and don't think I'll have a...
  3. F

    FLU419 SEE HMMH HME Owners group

    Well that's a bummer hopefully you can find a good used trans. I never thought about adding air horns but at 110 to 120psi they will work great.
  4. F

    FLU419 SEE HMMH HME Owners group

    And when you get all four on how close was are estimated guess on pintle height
  5. F

    FLU419 SEE HMMH HME Owners group

    They look good. Did you use down rigger to break beads. And if you need help finding your hood (kinda like where's waldo) I now where it is. I went with brand new pistas (5yrs old) and wish they were a little wider otherwise they are perfect. Let us know if they rub or if you had to adjust bump...
  6. F

    FLU419 SEE HMMH HME Owners group

    That makes work look fun flufarm, I hope the drain tile isn't damaged.If you do stick your head in the water to look in the tile we need a pic of that. I cleaned out my fuel tank vent (muddobbers) and to stop that from happening again stole the rear axle vent tube off a junk 04...
  7. F

    FLU419 SEE HMMH HME Owners group

    Finished installing drivers side front wheel seal and got to thinking about the brake pad wear wires, I will never in two life times wear out the pads. It's not like the other mogs that go on 100 mile camping trips, has anyone removed there wires and if so does it cause a problem with indicator...
  8. F

    FLU419 SEE HMMH HME Owners group

    Ok did some research on the dash bulbs, the original bulb is a k15617 t3 2w ba9s hard to find and expensive when you do 5.00 apiece+, I ordered 3797's box of 10 for 7.58. 3797's are a t2 (2.75) instead of t3 (3.25) that means the glass bulb is shorter should only be a problem if i put the little...
  9. F

    FLU419 SEE HMMH HME Owners group

    Mine is at 32 to center of ring but it's got new pista's on rear and sitting on jack stands on front just high enough to get tires off (replacing wheel seals) so i'd say closer to 33 with front down on new tires.
  10. F

    FLU419 SEE HMMH HME Owners group

    Quick question, does anyone have a bulb in there voltmeter gauge or did the military remove them because there to bright? I have seen video of see's and there meter is not lit up either. I notice all the other gauges have little rubbers on the bulbs and mine are fairly dim. I get the lets be...
  11. F

    FLU419 SEE HMMH HME Owners group

    Sod poodles is one I've never heard before lol. When i got it the safety switch would make a click (weak) but no power was getting to start button then it stopped clicking alltogether. After cleaning it was a loud click and instant power to wire behind start button and ohyeah! it works, it...
  12. F

    FLU419 SEE HMMH HME Owners group

    First off Thanks flufarm my see came with a remote starter switch and i remember a few pages back you cleaned your clutch safety switch and it worked for you so i took mine out and used the smallest cal brass brush .22 out of my gun cleaning supplies and cleaned the female side and emery cloth...
  13. F

    FLU419 SEE HMMH HME Owners group

    I'm hoping i never have to tilt the cab... I did get the valve out and cleaned up but the roll pin did embed half way up the first ramp so i filed it with a points file and it works great. I am thinking a lot of these 4x4 switches get thrown away when they get gritty and someone reams on it and...
  14. F

    FLU419 SEE HMMH HME Owners group

    thanks alpine, i was thinking that roll pin had imbeded into the plastic but your right even with a screwdriver pushing it down its gritty and sticky. maybe i can find a mechanically inclined 5 yr old to climb in there and take it off, luckily i just removed the spare tire hope i don't loose any...
  15. F

    FLU419 SEE HMMH HME Owners group

    new guy here and first off thanks to everyone for all the info. i have been working on my newused see so far fixed a 100 things with only a 100 to go. my 4x4 switch wouldnt move but it looks newish under the cab, if i press down on the plastic notched sleeve inside it turns just fine im thinking...
  16. F

    test

    test, test, test
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks