tm america
Active member
- 2,600
- 24
- 38
- Location
- merrillville in
think you have a typo the 11.00s will give you a top speed of about 60-62 and 395 will give you a top speed of about 69-72
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
395s WILL fit on a stock Deuce!!!
- Thread starter 100dollarman
- Start date
jayjetseck
New member
- 119
- 0
- 0
- Location
- manchester , pa
so 395 equals 15.5 ,right just trying to make sure. found 4 15.5 x 20 for 150 bucks with 90% tread shipping 250 so i didnt think that was to bad!! so now for the hemtt wheel modify ..
- 10,350
- 77
- 48
- Location
- Meadows of Dan, Virginia
"395" is the width in millimeters, but don't forget to include your aspect ratio, "80" or "85", which will give you the height. Furthermore, what matters when figuring diameter in the end is the "rolling" radius, which is used when figuring the revs/mile.
For the six 395/85R20 MV/Ts that I have for sale, the revs/mile is 445.....
1 inch=24.5 millimeters
- 3,657
- 27
- 48
- Location
- Dallas, Texas
I went back and corrected it. 59 is 2650RPM by the GPS and the tach. Tach could be off. The 395 speed was calculated relative to the "56MPH 2650RPM" figures seen in the manuals. I was assuming 56MPH was 2650RPM. No way to measure RPM except the tach.
DMgunn
New member
- 430
- 0
- 0
- Location
- SE North Dakota
Close, but 1 inch actually equals 25.4 mm.
Using the info on the sidewall is not a precise method of measuring size. It'll get you in the ballpark, but don't make any important decisions without getting the true dimensions.
DavidWymore
Well-known member
- 1,598
- 164
- 63
- Location
- El Centro, CA
OK Hundy, now make 'em fit DUALED...
Last edited:
frodobaggins
Active member
- 2,861
- 16
- 38
- Location
- Ruston, La
25.4 millimeters
- 10,350
- 77
- 48
- Location
- Meadows of Dan, Virginia
Correct, 1 inch =25.4 millimeters...brain missing a gear...or two.....
Planning on itOK Hundy, now make 'em fit DUALED...
DeuceNewb
Member
- 397
- 6
- 18
- Location
- Wilmington, NC
Ok you've got me convinced. This looks sweet and will be much easier than bobbing my deuce. Now i need to find 6....maybe 8 tires
DavidWymore
Well-known member
- 1,598
- 164
- 63
- Location
- El Centro, CA
I wanna see.
jrou111
New member
- 699
- 1
- 0
- Location
- Birmingham, AL
I still have 7 395's sitting in my garage. I've got to get around to fixing axle seal leaks on all 3 axles first.
first.Give me a few weeks, I will post some pics.
JTugwell
New member
- 134
- 3
- 0
- Location
- Pensacola, FL
i will be in touch with you in a month or so.
503m715
Member
- 93
- 2
- 8
- Location
- canby, Oregon
Mark, I have read the posts, but did not see what tube size you used with the stock rim?
100dollarman
New member
- 987
- 5
- 0
- Location
- Lucerne Valley, Ca. 92356
I have a tire guy nearby do the dirtywork for me--- But, I am pretty sure he uses the stock tubes- I will ask him next time I see him to make sure.
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 757
- 113
- Location
- Cincy Ohio
Wow! Stock as in 900x20?! You need to use 1300/1400 tubes.
503m715
Member
- 93
- 2
- 8
- Location
- canby, Oregon
Thanks Guy's, I want to get tubes this week so I can hopefully get some big tires on mine.
deuce808
New member
- 9
- 0
- 0
- Location
- Alpharetta Ga
395
that deuce with 395's... Are those on STOCK rims....
that deuce with 395's... Are those on STOCK rims....