• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Air Brake Info and Troubleshooting

Reworked LMTV

Reworked LMTV

Expedition Campers Limited, LLC
Supporting Vendor
1,511
1,178
113
Location
TN
chamber

:confused:
Oxyacetylene said:
The brakes on these trucks are wedge brakes. One of the guys at the local Truck Pro commented that wedge brakes are obsolete now with other self-adjusting brake systems. He asked if the truck was really old and was surprised when I told him mine was a 93 model. If you are completely new to air brake systems like I was, I suggest you do some reading about how the brake chambers work, it will help quite a bit when you start troubleshooting them.
Wait, wasn't replacing this a bit on the DANGEROUS side?
Here is a link to a Haldex catalog that lists wedge brake chambers:http://www.haldex.com/Documents/hbsna/Actuator-Spring_Brake/L00092W Actuators Catalog 2-2012.pdf

The rear chambers are a trade size 9/12, which means the inside (service) diaphragm is a trade size 9, and the outside (parking) diaphragm is a trade size 12. On these the parking brake portion is removable, although I would probably not recommend it. Due to safety concerns, the parking brake section on most new style chambers is crimped closed so you can't open it. There is info online about the dangers of the parking brake springs if you are curious. The service brake side of the chambers can be accessed, just remember to cage the brakes before you open it.

On my truck, I had and air leak in the rear when applying the service brakes (brake pedal). I was able to trace the air to the vent line that runs up to the frame rail and vents there. This pointed to a leak in the service brake diaphragm which was allowing air into the vent line. You can pick up a size 9 seal for under $10. The only caveat is that with the factory seal, the plunger piece is glued to the seal. Aftermarket seals are not made this way. So, for the cost I decided to just attach the plunger piece back to the new seal. I removed the old seal, peeled it off the plunger, scraped the plunger, wire brushed it, cleaned with alcohol, and applied contact cement. So far so good on the repair. I think there is probably a better adhesive option, but not that I could get locally to fix mine in a hurry.

In this pic, you can see one of the factory seals on the left with the plunger attached. The plastic bushing shown has been removed from the one on the right while I was repairing it. On the right is the aftermarket seal with the plunger piece glued back to it. The factory seal was shaped so that the center was raised, the aftermarket one is not, but works just fine as far as I can tell.
View attachment 562126
Click to expand...
Was'nt replacing these a bit dangerous?
 
Oxyacetylene

Oxyacetylene

Active member
Steel Soldiers Supporter
518
179
43
Location
Stoneville, NC
Floridianson said:
I would be will to bet that 99% of the death was someone did not cage the can before removing the clamps. 1% got careless with the cap when caged.
Click to expand...
I would probably just replace the piggyback assembly if the emergency brake side went bad. You could have an accident even doing the service side, but the emergency park spring is completely contained in the rear piggyback section so it's safer than trying to replace the diaphragm on the emergency side.
 
Floridianson

Floridianson

Well-known member
Steel Soldiers Supporter
7,409
2,503
113
Location
Interlachen Fl.
I did a right up about it on the 939 series and I just did my trailer in 20 minutes both sides. The problem with the cans with the safety tabs is it has to go side ways to come off or go on. I was about ready after I got the cap off to take a cut off wheel and cut the safety tabs when I did my 939. I just fought with it and got it right the first time but if I ever do it again I will cut off the safety tabs and install the cap straight on.
Don't do this!!
 
D

Dave21

Member
31
2
8
Location
Las Vegas NV
Location of air gauge transmitters location am a M1078 A1 .

Could anyone point out the location of the air gauge transmitters on a M1078A1 with ABS brakes . On an A0 it's on the left hand side opposite the brake pedal but on an A1 that is a location for part of the ABS system .
 
You must log in or register to reply here.
111,192members
165,488threads
2,328,804posts
1,269online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks