GTRealest911
New member
- 18
- 9
- 3
- Location
- NJ
I'm now checking voltage at relay panel and x1 is 11v and x2 22v?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Batteries
- Thread starter GTRealest911
- Start date
GTRealest911
New member
- 18
- 9
- 3
- Location
- NJ
Problem resolved.
Ronmar
Well-known member
- 3,846
- 7,475
- 113
- Location
- Port angeles wa
What was it?
GTRealest911
New member
- 18
- 9
- 3
- Location
- NJ
Operator error when i installed wire to battery. i got truck started with new pump
GTRealest911
New member
- 18
- 9
- 3
- Location
- NJ
Ronmar
Well-known member
- 3,846
- 7,475
- 113
- Location
- Port angeles wa
So what are we looking at here? I recognize the hydraulic pump
what model fuel pump is that?
coachgeo
Well-known member
- 5,147
- 3,462
- 113
- Location
- North of Cincy OH
captured springs point to either an offroad tanker truck or an Adventure Camper. If a camper....... ... there is also a forum in here for Military Campers that would love a discussion on what your up too. Well on second thoughts..... even if it is a tanker the info on your mount system would still help the camper builders
- 2,034
- 5,224
- 113
- Location
- Portland, OR
But - why? Just adds needless complexity. I don't see the benefit - I'm skeptical of the marketing BS. Not an ideal location and what the hell is with the hose management here? More thought should go into installation and routing - honestly would have been better to just forget about it altogether but I digress....
GTRealest911
New member
- 18
- 9
- 3
- Location
- NJ
The hose routing of hydraulic pump is temp. i upgraded my fuel tank to 95 Gallons. The captured springs are original to chassis,my truck was former mobile command center, it was missing from chassis when i saw it on Iron Planet.
Ronmar
Well-known member
- 3,846
- 7,475
- 113
- Location
- Port angeles wa
Ok, of all the messed up things I have seen people do to diesel fuel systems, not understanding fully how they work, I am finally able to say this isn’t so bad… the pump looks like it has adequate flow(100-165GPH?) usually what I see is someone throwing one of those autozone inline diesel pumps in there not realizing they cannot flow enough fuel to allow the pressure regulator to reach its specified pressures. starving MUI or HEUI injectors for fuel will kill them…
I do wonder how the 15ish psi this pump delivers will effect the way the pressure regulator controls the pressure in the injector gallery/fed to the injectors. You need to measure the secondary fuel pressure between governor and secondary fuel filter. There is a test port on a T fitting for this purpose. Should be ~20PSI at idle and ramp smoothly up to ~60PSI by peak torque/1550 RPM… i suspect it is probably running higher. How this will effect operations I am not sure, too much pressure could effect cup and injector sealing ability forcing fuel past the seals into the cylinder or out the top, or into the coolant…
I like Generals question, why? The cat fuel system is just fine and the injector operation and tune are based on its specific operation and pressure delivery, especially in the mechanically governed diesel. The only issues I have seen with it stem from lack of maintenance and mis-diagnosis of leaks allowing air in…
I do wonder how the 15ish psi this pump delivers will effect the way the pressure regulator controls the pressure in the injector gallery/fed to the injectors. You need to measure the secondary fuel pressure between governor and secondary fuel filter. There is a test port on a T fitting for this purpose. Should be ~20PSI at idle and ramp smoothly up to ~60PSI by peak torque/1550 RPM… i suspect it is probably running higher. How this will effect operations I am not sure, too much pressure could effect cup and injector sealing ability forcing fuel past the seals into the cylinder or out the top, or into the coolant…
I like Generals question, why? The cat fuel system is just fine and the injector operation and tune are based on its specific operation and pressure delivery, especially in the mechanically governed diesel. The only issues I have seen with it stem from lack of maintenance and mis-diagnosis of leaks allowing air in…
Third From Texas
Well-known member
- 2,766
- 6,498
- 113
- Location
- Corpus Christi Texas
I'd need to add a skid plate under those filters.
Because I scrape stuff with my truck and those look important to keeping it running.
Not knocking the relocate, though. I've seen some crazy relocation of the hydraulics and air filters.
Because I scrape stuff with my truck and those look important to keeping it running.
Not knocking the relocate, though. I've seen some crazy relocation of the hydraulics and air filters.