srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
brad you only want 150 for the truck? i love those trucks!
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Chevy G7105 1.5-Ton Panel (K51) or G7116
- Thread starter res0wc18
- Start date
nattieleather
Well-known member
- 1,883
- 145
- 63
- Location
- Cleveland, OH
Ok I did a search on the old WWW and I found one little bit of info on the interior of the K-51. Not much to go on, but it gives you a little idea. If you have past issues of Army Motors I know they showed the inside of one that was restorded by an Italian collector, but for the life of me I can't say which issue. Maybe contact the MVPA and see if they know. I think the article had something to do with a convoy in Italy to mark the end of WWII or something like that.
Anyway here is the link for the pict. File:SCR-299dooropen.jpg - Wikipedia, the free encyclopedia
And this is the radio set so basically all this went into the truck File:SCR-299hallicraftersAd1942.jpg - Wikipedia, the free encyclopedia
Hope that helps. Good luck finding a K-51 they are scares. Might have to look overseas
Anyway here is the link for the pict. File:SCR-299dooropen.jpg - Wikipedia, the free encyclopedia
And this is the radio set so basically all this went into the truck File:SCR-299hallicraftersAd1942.jpg - Wikipedia, the free encyclopedia
Hope that helps. Good luck finding a K-51 they are scares. Might have to look overseas
Wolfen
Active member
- 942
- 153
- 43
- Location
- Woodburn Oregon
Thank you. The Problem with getting one from Overseas would be the Cost of Shipping.
Last edited:
B460FA
New member
- 10
- 0
- 0
- Location
- Orange, TX
What views of the interior would you like?
Steve
Steve
Wolfen
Active member
- 942
- 153
- 43
- Location
- Woodburn Oregon
I would like Pictures of everything. So far, I have only been able to find one Picture of the Interior. Any help, would be Appreciated. 
B460FA
New member
- 10
- 0
- 0
- Location
- Orange, TX
From SCR-299 in Italy 2008 Column of Liberation rally.
Some views inside. I have more detail if you need it.
Steve
Some views inside. I have more detail if you need it.
Steve
Attachments
Wolfen
Active member
- 942
- 153
- 43
- Location
- Woodburn Oregon
More Detail, would be Appreciated. I see that yous does not have the Chest on eaxh side that I have seen in other Pictures.
I see that yous does not have the Chest on eaxh side that I have seen in other Pictures.
B460FA
New member
- 10
- 0
- 0
- Location
- Orange, TX
I only wish it was mine. It is nicely equipped with everything.
Attachments
Wolfen
Active member
- 942
- 153
- 43
- Location
- Woodburn Oregon
It is a very nice looking Truck.
Wolfen
Active member
- 942
- 153
- 43
- Location
- Woodburn Oregon
Does anyone know where I could get the Seats for a K51? If I buy the one I'm looking at, the Seats are missing. Reproductions, NOS, or take outs, are ok. Plans so I could have some made would work also.
bradcckw
New member
- 17
- 0
- 0
- Location
- Langley,Washingtion
Wolfen
Active member
- 942
- 153
- 43
- Location
- Woodburn Oregon
I wish I had the Money.
mud brother
New member
- 4
- 0
- 0
- Location
- acton , ca
same here . if i had the cash i would be makin a road trip this week .
chaoticone
New member
- 27
- 0
- 0
- Location
- Pageland South Carolina
I have a G7117 or 7116, not sure which it is yet. It has a dump bed but the Hyrdaulic cylinder is missing. It's pretty rough. I'm thinking of putting the axles, transfer case and winch under a 77 chevy 3/4 ton but I kind of hate to. I'm afraid the parts may mean more to someone else. Let me know if I can help.
Billy Buzzard
New member
- 1
- 0
- 1
- Location
- British Columbia,Canada
I don't know if I am in the right section or not so is there someone who can perhaps redirect me?
I have a 1941 1 1/2 Ton Chevrolet Panel truck (G7105 /K51) and due to advancing age (mine not the truck's) don't think I'll ever get to this restoration project.Thanks for any assistance.
Billy Buzzard
I have a 1941 1 1/2 Ton Chevrolet Panel truck (G7105 /K51) and due to advancing age (mine not the truck's) don't think I'll ever get to this restoration project.Thanks for any assistance.
Billy Buzzard
- 9,604
- 1,493
- 113
- Location
- mid- michigan
This post is why Steelsoldiers want photos posted directly to the site , dead link to pics doesn't help anybody.mine is sleeping,, in the corrner,, like a bear. in long hibernation
early K 51 panel non radio unit , civi gauges,
has anyone found a frame stamp on there's?/ i started a thread on the g503, about frames and chevyies etc..
i need a better set of running boards,, and rear fenders,, some one wanted singles, hense why she's sleeping for awhile,, i'd be interested if any are for sale,, so i could repo the running boards rear fenders, and maybe resale,, i have a quad mt for trade,, email me the list, jefferychester@yahoo.com jc
And this link no longer works.
WW2Chevy
Active member
- 113
- 57
- 28
- Location
- Bloomington, IL
Link works... dismiss the ad, and the pic underneath is of the truck in question, in the back lefthand corner.
- 3,913
- 2,725
- 83
- Location
- Edmonton, Canada
Hello BB,
If I'm reading you correctly you're wanting a good home for a truck. I'm sure you'll get directed by a director to add a province to your location and to the membership up-grade so you can run an add in the claSSifieds once you pay a tiny fee.
I sent you a Private Message PM which will be in your 'notifications' with some contact info.
- 275
- 3
- 18
- Location
- pefferlaw ontario
My K-51 has moved from Ontario to Norway Via Southern Cal. , is now for sale on Milweb , I hope that it gets finished as it should , all the coms parts I collected went with the truck, sure has traveled in the last 2 years,
Wolfen
Active member
- 942
- 153
- 43
- Location
- Woodburn Oregon
I wish it was mine