Drash generator 35kw with 96,000 BTU A/C?

[smeeg]

Hello recently purchased a Drash generator 35kw with 96,000 BTU A/C
(Paid $11,500 with just 4 original hours on it)
i want to run the A/C from the building power (shore power) I don’t know where to acquire or what to call the military style plugs for the shore power?
Also the “j5 120volts input” I’m assuming is a trickle charger/block heater?
Id like to find a plug for that as well if that’s the case. Any help is greatly appreciated.

(I know I can change out the military plugs for civilian plugs but would like to keep it original if possible)

 

[Guyfang]

Look at your jacks. Get the part number/NSN of the jack. Then look them up in your web browser. Look for the plug the mates to it.

Also try PM'ing Supman in the forum. He is sharp with these things.

 

[smeeg]

Look at your jacks. Get the part number/NSN of the jack. Then look them up in your web browser. Look for the plug the mates to it.

Also try PM'ing Supman in the forum. He is sharp with these things.

Whats a “jack”? The receptacles I posted pictures of??

 

[Suprman]

The shore power is an input so you can run the ac without the gen. There is usually a 60a output connection. It is a 3 phase generator.

 

[CARNAC]

Whats a “jack”? The receptacles I posted pictureOnes of??

One of these is Jack, the other is jack, the other is jack, the other is jack, and the last one is jack.

 

[jbayer]

Hint-The connectors are labeled "J"1 and "J"5. Connectors are either a "P", or a
"J".

 

[smeeg]

Hint-The connectors are labeled "J"1 and "J"5. Connectors are either a "P", or a
"J".

I tried googling that before I posted Where can I find the connectors for sale?

 

[DieselAddict]

Hello recently purchased a Drash generator 35kw with 96,000 BTU A/C
(Paid $11,500 with just 4 original hours on it)
i want to run the A/C from the building power (shore power) I don’t know where to acquire or what to call the military style plugs for the shore power?
Also the “j5 120volts input” I’m assuming is a trickle charger/block heater?
Id like to find a plug for that as well if that’s the case. Any help is greatly appreciated.

(I know I can change out the military plugs for civilian plugs but would like to keep it original if possible)

Do you have 3 phase power available at your building?

 

[smeeg]

Do you have 3 phase power available at your building?

Yes

 

[smeeg]

The shore power is an input so you can run the ac without the gen. There is usually a 60a output connection. It is a 3 phase generator.

Correct I’m looking for the female/male nato connectors for the shore power

 

[jbayer]

http://www.amphenol-aerospace.com/pdf/catalogs/connector-basics.pdf

 

[DieselAddict]

Yes

Roger that.

http://www.amphenol-aerospace.com/pdf/12-052.pdf

 

[smeeg]

Roger that.

http://www.amphenol-aerospace.com/pdf/12-052.pdf

Thanks that’s a lot of info might just swap these for civilian connectors didn’t realize they had so many choices

 

[155mm]

I may have a connector that will fit that J1. What is the dimensions inside the collar? Does it give you an amp rating for it? 60amp? 100 amp?

 

[smeeg]

I may have a connector that will fit that J1. What is the dimensions inside the collar? Does it give you an amp rating for it? 60amp? 100 amp?

I’ll take a measurement and see if has any ratings on it Tommorow

 

[155mm]

This is what i came up with so far.

https://www.steelsoldiers.com/attachment.php?attachmentid=674267&d=1491493802

The above link is for the hvac, the below link is for the genny

https://www.steelsoldiers.com/attachment.php?attachmentid=674268&d=1491493840

the next info was stolen from the above link



it calls for 80 amps, so my guess it will require a 100amp plug

 

[uniquify]

I’ll take a measurement and see if has any ratings on it Tommorow

Look inside the inlet connector above the bottom center pin. It should have a number like one of these:
32-12 ( 60 amps, 5 pins)
44-12 (100 amps, 8 pins)
52-12 (200 amps, 8 pins).

 

[smeeg]

I may have a connector that will fit that J1. What is the dimensions inside the collar? Does it give you an amp rating for it? 60amp? 100 amp?

It’s 2 1/4” inside the collar say 44-12p so 100amps

 

[155mm]

I have one left. It only has short tails on the end so you would need to add more cable to go to the building.

 

[155mm]

I might also have a plug to fit the J5


.