mrgerke81
New member
- 38
- 0
- 0
- Location
- Raleigh, NC
Installed a 10 ton dump kit on the deuce this weekend. Still have some loose ends to tigh up.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Dumping Deuce
- Thread starter mrgerke81
- Start date
clinto
Moderator, wonderful human being & practicing Deuc
Staff member
Administrator
Super Moderator
Steel Soldiers Supporter
Supporting Vendor
- 12,596
- 1,133
- 113
- Location
- Athens, Ga.
Very good... you will love it. I get a lot of use out of mine. Let's see some more pics!
How did you do the hinges and the pump?
How did you do the hinges and the pump?
m52a2
New member
- 89
- 0
- 0
- Location
- Jackson, Michigan, USA
How are you powering your hydraulic pump. Tell us about the hydraulics that supply the dump hoist. how about hydraulic controle, resivoir ?
mrgerke81
New member
- 38
- 0
- 0
- Location
- Raleigh, NC
Here is a pic of the pump unit. I purchased the kit from Northern Tool. It came with all the hinges, dump mechanism, and pump. I am going to pull 12 volts off of one battery. I am also installing a battery equalizer to balance out the two.
Attachments
Offroadfabworks
Banned
- 1,331
- 5
- 0
- Location
- decatur alabama
Looking good ![[thumbzup]](https://www.steelsoldiers.com/images/smilies/icon_smile_thumzup.gif "Thumbs Up [thumbzup]")
Flea
Member
- 457
- 10
- 18
- Location
- Northeast TN
Looks good to me, boss.
- 1,299
- 9
- 38
- Location
- (near) Xenia, Ohio
It'll make your troop-seat passenger behave.
56FordGuy
New member
- 19
- 0
- 1
- Location
- Gallatin TN
Really nice job. Gives me ideas.
I'd love to know what the part number on the hydraulic motor is. I work on electric forklifts, and that motor looks very, very similar to the 24 volt motors that are used on some electric pallet jacks. I think it may be possible to 'bolt in' a 24 volt motor, but I'd need the model number to be sure.
I'd love to know what the part number on the hydraulic motor is. I work on electric forklifts, and that motor looks very, very similar to the 24 volt motors that are used on some electric pallet jacks. I think it may be possible to 'bolt in' a 24 volt motor, but I'd need the model number to be sure.
bmH1065
New member
- 106
- 0
- 0
- Location
- Iola, Kansas
How much weight can you dump with this unit?
joeM62
Member
- 551
- 1
- 18
- Location
- Cedartown/GA.
you have nice setup, i'm looking to do the same thing to mine.
- 2,102
- 30
- 38
- Location
- Delta Junction, Alaska
Looks great. I mounted a spare deuce bed on a farm wagon, but use the tractor hydraulics to power it. You have to be careful with them, and always be on level ground, when you raise the bed.
Lee in Alaska
Lee in Alaska
muddog7375
New member
- 43
- 0
- 0
- Location
- Eau Claire WI
Matbe a stupid question....BUT, do you get alot for noise comming from the bed when just driving it compaired to a non dump?
BobM
Member
- 593
- 6
- 18
- Location
- Fillmore, Indiana
If you have a Tractor Supply (or similar) store near you, they can also get you rubber belt material to put on your framerails.ranchhopper said:
muddog7375
New member
- 43
- 0
- 0
- Location
- Eau Claire WI
Thanks for the answers...
When I get Deuce this is what Id want...
I was also thinking of some kind of locking pin thing to lock the bed down...
When I get Deuce this is what Id want...
I was also thinking of some kind of locking pin thing to lock the bed down...
muddog7375
New member
- 43
- 0
- 0
- Location
- Eau Claire WI
Thanks for the answers...
When I get Deuce this is what Id want...
I was also thinking of some kind of locking pin thing to lock the bed down...
When I get Deuce this is what Id want...
I was also thinking of some kind of locking pin thing to lock the bed down...
5tonpuller
Active member
- 573
- 27
- 28
- Location
- Thompson, Pa
Here is a few I seen up to Kublos. They look to be heavy units and he did a good job with them.
I still would like a 5 ton dump. But I think I would get my self in trouble with it.
Shameless plug
I still would like a 5 ton dump. But I think I would get my self in trouble with it.
Shameless plug
Attachments
- 2,960
- 31
- 48
- Location
- Tiro, Ohio
As far as noise, I don't notice any more noise than usual driving on-road. If I'm off-road, the bed creaks and groans pretty good. Don't have a locking pin for when the bed it down. The bed does have down-pressure, and hydraulic pressure keeps it down.
Dennis
Dennis
- 9,580
- 218
- 63
- Location
- Dickson,TN
Got any pics if the back end where the hinges are? I've installed alot of dumps on trucks but I never have on a deuce and I want one.
What is the weight rating for your hoist? I know you said 10 tons but it looks a little light for a 10 ton hoist.
Looks like you may have it mounted a little too far back on the frame. Look at the pics 5tonpuller posted. The hoist is mounted about right to keep from overloading the front of the bed. I've looked at these beds and they are a little light for a dump bed unless you don't load it very heavy or beef up the bed. When I get around to mouting mine I'm going to box the main bed channel so I won't have to worry about it bending under load.
What is the weight rating for your hoist? I know you said 10 tons but it looks a little light for a 10 ton hoist.
Looks like you may have it mounted a little too far back on the frame. Look at the pics 5tonpuller posted. The hoist is mounted about right to keep from overloading the front of the bed. I've looked at these beds and they are a little light for a dump bed unless you don't load it very heavy or beef up the bed. When I get around to mouting mine I'm going to box the main bed channel so I won't have to worry about it bending under load.