Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
I am going to make one of these and would like to have any pictures to go by I can get, my memory is a little fuzzy on some things.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Fav/Dpv 1009
- Thread starter Csm Davis
- Start date
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
What nobody has pics of one of these? I know at least 2 were sold through govliquidation a few years back.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Bump for the weekend crowd somebody has got to have a picture or two, can it be I am tge only one who has seen one?
- 3,752
- 1,529
- 113
- Location
- North Carolina - FINALLY !
I'm going to plead ignorance. I know what a 1009 is, but not a FAV/DPV?
- 10,498
- 6,631
- 113
- Location
- Camp Wood/LC, TX
FAV is Fast Attack Vehicle? There was a M1009 version? Too cool, thought there was just M151 versions.
85CUCVtom
Active member
- 712
- 26
- 28
- Location
- Lakewood, Ohio
I didn't know the term "fast" was in a M1009's vocabulary.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Fast Attack Vehicle / Desert Patrol Vehicle
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
NDT and 85CUCVtom whats even funnier is one I saw was only in service CUCV with factory ac that I ever saw and it was still on the DPV which is what I think they were built for.
Last edited:
cpf240
Active member
- 1,479
- 5
- 38
- Location
- Free in Northern Idaho
Its all relative... relative to the other CUCVs, the M1009 is a rocket....
85CUCVtom
Active member
- 712
- 26
- 28
- Location
- Lakewood, Ohio
That is true.
85CUCVtom
Active member
- 712
- 26
- 28
- Location
- Lakewood, Ohio
Should be a cool build. I've tried to Google pictures without luck. What's your build plan looking like?
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Got a few blazers parting out want to get started soon probably use the worst body and cut most of it away.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Been looking at this and so I can drive it I will be using a windshield frame off of a 5ton and leave the fire wall of the blazer intact. Now I have two different ideas for gun mounts and they are a pedestal or ring mount the ring mount will be heavier and I don't remember ever seeing a fav with one, input is welcome but leaning hard towards the hard mount.
nattieleather
Well-known member
- 1,883
- 145
- 63
- Location
- Cleveland, OH
I googled it also and couldn't find any pictures of it. So according to the laws of the internet...no pics means they don't exist! 
So make it how ever you want I'm sure it will be cool.
I would think that if someone made a FAV/DPV M1009 that to my mind the cargo cover would come off and a pedestal mount would be mounted behind the front seats with a M2 mounted on the pedestal. No ring mount just a place for a guy to stand in the back and hammer away on the fiddy. I would think the doors would be removed for faster entrance and egress. Maybe larger tires with cut fenders and of course the flat sand paint. Some big skid plates on the bottom to protect everything and away you go. Maybe remove the tail gate and put a half gate sheet of metal to keep stuff from falling out. Oh and some storage chests/benches over the back wheel wells too. Okay I'm done. Good luck with the project.
Joe OHMR Ret.
So make it how ever you want I'm sure it will be cool. I would think that if someone made a FAV/DPV M1009 that to my mind the cargo cover would come off and a pedestal mount would be mounted behind the front seats with a M2 mounted on the pedestal. No ring mount just a place for a guy to stand in the back and hammer away on the fiddy. I would think the doors would be removed for faster entrance and egress. Maybe larger tires with cut fenders and of course the flat sand paint. Some big skid plates on the bottom to protect everything and away you go. Maybe remove the tail gate and put a half gate sheet of metal to keep stuff from falling out. Oh and some storage chests/benches over the back wheel wells too. Okay I'm done. Good luck with the project.
Joe OHMR Ret.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Yeah joe but your not getting radical enough onthe body work or lack thereof, the firewall and dash stay but not much else.
- 10,498
- 6,631
- 113
- Location
- Camp Wood/LC, TX
After thinking about it, it makes sense why the Blazers were not widely converted to this config. Take a Blazer, remove the top, add larger wheels, a fold down windshield, and wala you got a HMMWV.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Yeah a lighter, narrower, better working vehicle and if you used the 1028a2 a lot stronger one!
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Okay finally getting around to this and I am wanting to build this starting with the tires, humvee 24 bolt, which will mean that the D60 and 14 bolt are needed. That will probably mean that I use the 1008 frame and the 1009 firewall and floor. This will be a build trying to stay with what I could source while on active duty and if I can find my old pictures of an actual one that was in service, built like it. Any guys that actually used one or built DPV's out of other vehicles please let me know if you see something that is right or wrong.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Something like this but less body panels and here's one cool cucv with a gun mount and a MK19!
