- 3,960
- 6,418
- 113
- Location
- MA
If you do, PM me your address. I have a couple extra of those throttle knarps, be happy to drop one in the mail.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Finally joined the MEP-803A club...
- Thread starter robson1015
- Start date
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
Thank you ... I may need to do that -
Maybe a dumb question but what does the button on the freq. cable do? When my unit is running I can adjust the Hz but twisting the knob. I have it set on 61Hz. When under load does the governor automatically rev up the engine ?
Maybe a dumb question but what does the button on the freq. cable do? When my unit is running I can adjust the Hz but twisting the knob. I have it set on 61Hz. When under load does the governor automatically rev up the engine ?
- 3,960
- 6,418
- 113
- Location
- MA
The center button allows the RPMs to change. It drops them down to 1200 or so (but the reality of the machine in my opinion, and others... is that you never want to slow this machine down). If you open the door on the cable side, you can trace the line right back to the governor control... that turns and has two screws which stop the movement. It just pulls that control from low rpm to high, for the lack of a better description.
- 3,960
- 6,418
- 113
- Location
- MA
Its the twisting motion on the cable knob which allows for fine rpm tuning, basically... to tweak the rpms due to load, to hit 60hz.
- 17,476
- 25,839
- 113
- Location
- Burgkunstadt, Germany
Actually, it cost 72 dollars new. The two below listed companies supplied it to the gov. Part number: 347L-032-2, NSN: 2190-01-385-9030
Phone numbers
Could not hurt to call!
| ARENS CONTROLS COMPANY, L.L.C | DBA ARENS CONTROLS | 3602 N KENNICOTT AVE | ARLINGTON HEIGHTS | IL | 60004-1467 | UNITED STATES | ||||||||
| B.W. ELLIOTT MANUFACTURING CO., LLC | DBA ELLIOTT MANUFACTURING | 11 BECKWITH AVENUE | BINGHAMTON | NY | 13901-1726 | UNITED STATES |
Phone numbers
| 847-8444779 | 847-8444790 | ||||||||||||
| 697-7720404 | 607-7720459 |
Could not hurt to call!
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
Called both and both wanted to ass rape me...I'm willing to go $100 or so.
So if I have the Hz set at 60-61 without load does it take much adjustment when a load is applied??
So if I have the Hz set at 60-61 without load does it take much adjustment when a load is applied??
- 3,960
- 6,418
- 113
- Location
- MA
Depends if you are slowly adding load, or dumping your mother in laws hot tub AND deep fryer onto the circuit at the same time... but regardless these machines should take it and will only vary upon initial balancing.
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
AeroBase Group quote= $375.00
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
Got the MOV modification done today thanks to Kloppk...Thank You Kurt.
Also got a output lug wrench from flea bay...
Before
After
Last edited:
- 17,476
- 25,839
- 113
- Location
- Burgkunstadt, Germany
Did you try the wrench? There are several sizes. NEVER use it under power. Try and use it when the set is stopped, and you will understand why soldiers cut several inches off the handle.
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
The wrench is the correct size. It is not functional at full length with the lanyard attached. It's all good now.
- 17,476
- 25,839
- 113
- Location
- Burgkunstadt, Germany
I actually knew someone who tried to use one, while under load. Contractors are not supposed to assault Soldiers. I showed great restraint. His supervisor, did not.
Its funny now, but I thought he had come to an abrupt end when he flew backwards off the PU trailer and slammed into the Truck. By the time I got there, his supervisor had "Counseled" him. He had barely stood up from the shock, when she hit him. Then she sent him to the Dispensary. Good NCO.
Its funny now, but I thought he had come to an abrupt end when he flew backwards off the PU trailer and slammed into the Truck. By the time I got there, his supervisor had "Counseled" him. He had barely stood up from the shock, when she hit him. Then she sent him to the Dispensary. Good NCO.
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
No room for mistakes with genset under load...
Curious about the 3 piece ground rod - how much is normally used in the field??
Curious about the 3 piece ground rod - how much is normally used in the field??
- 17,476
- 25,839
- 113
- Location
- Burgkunstadt, Germany
Depends on who was looking. I almost never ordered 3 piece rods. Too expensive. I got the one piece rods. AND you could not cheat, unless you used a hacksaw. In Air Defence, we often were inspected by NATO wiesel's. They had no humor for short rods. A commander could loose his job if something went wrong. So we were pretty honest.
Other units, not so much. For me, the three piece rods always seemed too prone to becoming loose. Loose rod, bad ground. I have been bit bad by electricity two times. I am over Mr Overkill in this instance. The down side to the one piece rod is that you can not use the ground rod driver/puller. I have left about 42 miles of ground rod in Mother Germany's soil.
Later, when I worked as a NATO wiesel, the first thing I did was try the ground connections, and then tried to pull a rod up. It was sad face when something was loose or a rod was so poorly driven in the ground that a poor old, used up inspector like me, could pull it up.
Sometimes in the desert, we could not get a good ground with 5 pieces. Sometimes we drove 10-15 rods in the ground and wired them all up, to get a ground.
Other units, not so much. For me, the three piece rods always seemed too prone to becoming loose. Loose rod, bad ground. I have been bit bad by electricity two times. I am over Mr Overkill in this instance. The down side to the one piece rod is that you can not use the ground rod driver/puller. I have left about 42 miles of ground rod in Mother Germany's soil.
Later, when I worked as a NATO wiesel, the first thing I did was try the ground connections, and then tried to pull a rod up. It was sad face when something was loose or a rod was so poorly driven in the ground that a poor old, used up inspector like me, could pull it up.
Sometimes in the desert, we could not get a good ground with 5 pieces. Sometimes we drove 10-15 rods in the ground and wired them all up, to get a ground.
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
Got a load bank today, craig'slist for $50. Maxed out at 65% load with everything on 'high' setting and broiler. Got another 10% on the convenience outlet, total 75%. Ran it for 2 1/2 hours @ 75% load. All went well. I'll have to get a supplement heater or something to get to 100%. So far so good.
Attachments
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
Completed the pad for the 803A today...
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
50A inlet box to 50A breaker connected to interlock switch...Waiting on 50a box to mount on genny.
robson1015
Active member
- 515
- 134
- 43
- Location
- New Concord, Ohio
Covered the bottom 6x6 hole with hardware cloth today. Should be mouse proof and wasp proof.