LMTV Transmission Issues

[Suprman]

What was your trans issue again? It's a big job to swap a trans in that truck. I have heard of people dropping the trans and being able to slide it sideways and out but it's tight.

 

[Socommfg]

I have several LMTV transmissions with converters in stock. under 1500 miles on them. I agree, Fluid capacity is extremely important and the throttle position switch will cause the transmission not to operate properly. The throttle MUST be in the LOW position.

 

[Recce01]

Thanks for posting all of this. Great info to know!

 

[samsneed]

What was your trans issue again? It's a big job to swap a trans in that truck. I have heard of people dropping the trans and being able to slide it sideways and out but it's tight.

The ECU, control pad, wiring harness and engine speed sensor have all been replaced, transmission is still throwing code 56-33. According to the tm, I need to measure the main pressure in the transmission, since I don't have the computer, I'm either pulling the transmission or risking putting it into the shop and praying for an easy fix

Sent from my Pixel using Tapatalk

 

[scottmandu]

Has anyone actually changed out to the Transynd or any other DexIII fluids and have some serious miles logged (over a 1,000) with the new fluids?

I'm using Dex IV in my 1078A1 and have done so for 2500 miles. No issues knock on wood.

 

[wandering neurons]

In addition to my M1081, I've got an older RV with the MD3070 version of the Allison. I looked at my WTEC-II manual that I have, I had to troubleshoot DO NOT SHIFT in conjunction with some additional codes that were dependent on speed sensors. Good power and ground are critical for the ECU and the transmission. The MD3070 turbine and output speed sensors are outside the transmission and can be easily tested and replaced, maybe the same on the 3000.
The solution to my particular problem was to cut the three sets of sensor wires at the transmission and build a new shielded twisted-pair wire harness to the ECU to eliminate electrical noise that was causing my codes.
Also, it's not too hard to drop the valve solenoid body on this trans, that seems to be where a lot of other problems come from on the Allison trans. Clutches are pretty tough on these.
The LMTV uses a different model of Allison, your mileage may vary. Also check the IRV2.COM forum for instances of problems with this trans.

 

[langstonhs]

What was your trans issue again? It's a big job to swap a trans in that truck. I have heard of people dropping the trans and being able to slide it sideways and out but it's tight.

We were able to get our MD3070 transmission out, but with great difficulty because of the frame crossmember at the back of the transfer case. Getting both ends of the transmission/TC free at the same time so we could drop it down was a bear. Not looking forward to trying to fit it back up there. Do you have any tips for making the transmission removal and reinstallation process easier?

 

[Keith Knight]

This how I removed the transmission by myself.

 

[ckouba]

Keith-

That is all sorts of AWESOME!!!

 

[Reworked LMTV]

This how I removed the transmission by myself. View attachment 819241View attachment 819242View attachment 819243View attachment 819244View attachment 819245View attachment 819246View attachment 819247View attachment 819248

Where there is a will, there's a way!

 

[coachgeo]

Where there is a will, there's a way!

did you use the tranny bolts for the lifting eye...... or you buy longer bolts?

 

[Keith Knight]

Pretty sure I was able to use the original bolts.

 

[frank8003]

So you are worker bee, machinist, planner, welder, rigger, draftsman, owner, figure it outer, publicist, + procurer, amongst other jobs.
How the heck did you figure the center of balance?

Your posts about "how I did LMTV transmission myself" needs to be a stickie, but I have not found that database.
Informative, to the point, wonderful post.
Thanks

 

[Ronmar]

So you are worker bee, machinist, planner, welder, rigger, draftsman, owner, figure it outer, publicist, + procurer, amongst other jobs.
How the heck did you figure the center of balance?

Your posts about "how I did LMTV transmission myself" needs to be a stickie, but I have not found that database.
Informative, to the point, wonderful post.
Thanks

The specs for the trans lifting fixture are in the manual...

 

[Keith Knight]

I am an engineer and have a machine shop, but he’s absolutely correct the drawings are in the manual somewhere. I had them in my photo library so I thought they would be useful. They are spot on for the balance point. It makes the transmission float perfectly level. Sorry I haven’t posted earlier.

 

[hitekenterprises]

ho

This how I removed the transmission by myself. View attachment 819241View attachment 819242View attachment 819243View attachment 819244View attachment 819245View attachment 819246View attachment 819247View attachment 819248

how many hours does it take you to remove and replace it?

 

[Keith Knight]

That’s a loaded question, all the hours and days in preparation or if the bed, driveshafts, fabricating the hoist and special tool and trans removal about 5 days but the actual unbolt and rebolt new one maybe 8 hrs by myself.