kingzilla
New member
- 9
- 0
- 0
- Location
- Asheville, NC
A few times I have had the truck messed with and I am afraid they will release the park brake. Anyone have a easy solution to putting a lock on the brake?
thank you
seth
thank you
seth
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M923A2 easy way to put a lock on the park brake?
- Thread starter kingzilla
- Start date
dmetalmiki
Well-known member
- 5,523
- 2,029
- 113
- Location
- London England
I don't know the placement of the handbrake on your particular truck, But on my deuces and 5 tons the (extended) security chain runs around the handbrake and then locks up onto the steering wheel.
- 1,964
- 217
- 63
- Location
- Arizona
Leave the front red gladhand open. Then it won't matter where the parking brake handle is because there will not be any air in the system to release the spring brakes.
wreckerman893
Possum Connoisseur
- 15,629
- 2,054
- 113
- Location
- Akenback acres near Gadsden, AL
That is true but then they could push in the "Spring Brake Override" button and have a rolling vehicle with no brakes.
kingzilla
New member
- 9
- 0
- 0
- Location
- Asheville, NC
anyone work a way to get a pad lock on it?
- 1,450
- 121
- 63
- Location
- Gray, GA
Leave all the drain valves open on the passenger side step. All 4 tanks will be drained. Then it won't matter is the handle is kicked down or not.
- 1,964
- 217
- 63
- Location
- Arizona
That won't happen if there is no air in the tanks.That is true but then they could push in the "Spring Brake Override" button and have a rolling vehicle with no brakes.
kingzilla
New member
- 9
- 0
- 0
- Location
- Asheville, NC
If all 4 tanks are drained can the "Spring Brake Override" button release the brakes?
thank you
seth
thank you
seth
Ford Mechanic
Active member
- 1,805
- 7
- 38
- Location
- Edenton, NC
I will find a pic of the setup I did for a guy who was afraid his grand kids would kick his and disengage it. It involved a 1/4" piece of steel welded to the rear cab support coming out towards the brake with a 3/8" hole drilled in it. and it had a 1/4" horseshoe piece of metal on the other end with two 3/8" holes in it. It was made so he could slip a lock thru all 3 holes and it would prevent it from going down.
- 1,964
- 217
- 63
- Location
- Arizona
That is true but then they could push in the "Spring Brake Override" button and have a rolling vehicle with no brakes.
The more I think about this, what I said may not be entirely true. It is possible (I did not confirm) that the emergency gladhand at the front will only drain the wet tank and leave the others full. This may allow for the spring brake override to still function.
Swamp Donkey's solution is better. Open all the drains and ensure that there is no air in the truck at all. Then one could be sure that the spring brake override button would not disengage the spring brakes.
Stein12501
Member
- 190
- 4
- 18
- Location
- Tebbetts, MO.
I'm interested in doing something because this happened to me. I was helping the grandson down from the cab and his foot hit the brake handle. Rolled 3 foot down to the block next to my building and stopped. Scared the crap out of me. It would be nice if there were something similar to the locking E brake on the HMMWV's. Wheel chocks actually are the best way to keep this from happening.
- 737
- 14
- 18
- Location
- Bothell, WA
When there's gonna be kids in the cab and not me, wheels get chocked and the tanks get drained.
I'd close the valves when the tanks are empty though. Keep ambient air out.
I'd close the valves when the tanks are empty though. Keep ambient air out.
Last edited:
Yes, Both E gladhands are connected to the wet tank. There are check valves between the primary and secondary tanks and the wet tank so they wont empty. Open all the drain ports and call it good.
Other way you can do it is. Put a eyelit from a hasp lock and screw it onto the cab on that brace. Then run a eyelit or hook turnbuckle out towards your Brake handle. and if the hook in will go around the handle then tighten it down to it or you can also use a carabineer or snap lock to slip over the handle and tighten the turn buckle down. This way it can be removed when you are driving and wont rattle. I can work one up if pics would help. It would cost you under $20 to make it work.
Attachments
kingzilla
New member
- 9
- 0
- 0
- Location
- Asheville, NC
Is the pic just showing the e brake or it installed on it? Hard to see. thank you
just the mounting area.
acme66
New member
- 349
- 8
- 0
- Location
- Plains, Montana
I think you are all over thinking this. Pipe that slips over P-Brake handle about 8 inches long with chain loop welded on in center. Tab under Seat belt mount with length of chain welded on. Padlock chain to pipe. Chain isn't long enough to slip pipe up and off handle, handle can not be released. No waiting for air drain/build if you are just parked someplace quick. Had my son kick off the p-brake by accident, made me REAL conscious of always chocking the wheels. If I hadn't been standing next to the running board at the time I would have lost the truck and maybe him over a bank and into a pond.
Ken
Ken
Last edited: