- 16,766
- 24,079
- 113
- Location
- Burgkunstadt, Germany
You are assuming. Not a good idea. We see and hear from folks every week, that they do not have the Quad mod. Assume nothing, check everything.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Military MEP generator reset information
- Thread starter Daybreak
- Start date
69birdman
Active member
- 201
- 139
- 43
- Location
- Summerfield, Fla.
I've recently completed the fuse mod on my 99 803a. I found the exact fuse holder and fuses on ebay, like $11 dollars shipped. Paid for 2 pack of fuses, they sent 4. Have extras if you fellas have problems finding them.
maniatopoulosg
Member
- 116
- 8
- 18
- Location
- Miami, FL
tktsales
Member
- 86
- 13
- 8
- Location
- Yanceyville, NC
IN ZED254s photo there is a blue MOV / Varistor between terminals 7 & 8. Is that part of this mod or is that standard equipment. I will need to check my 2 older units.. I have read about the quad fuse issue before but my main unit is pretty new and I believe it is factory equipped with the update. Is there a way one can visually tell if a unit has the updated Quad circuit. I think my main unit is 2010ish.
On the 2 older units I have recently purchased, both of them have an inline fuse holder wired into one of the other terminal strips. I will need to look at that later this evening. It is not a high voltage fuse like this Quad fuse but I am curious if someone will be able to enlighten me as to what these fuses were installed for.. I will upload a few photos in the morning..
On the 2 older units I have recently purchased, both of them have an inline fuse holder wired into one of the other terminal strips. I will need to look at that later this evening. It is not a high voltage fuse like this Quad fuse but I am curious if someone will be able to enlighten me as to what these fuses were installed for.. I will upload a few photos in the morning..
Zed254
Well-known member
- 866
- 466
- 63
- Location
- S. Hampton Roads, VA
Check out this thread - and what Kloppk says about the MOV. https://www.steelsoldiers.com/showthread.php?148791-MEP-802-and-803-Main-generator-tip/page2
and this TM: https://www.steelsoldiers.com/showthread.php?165569-Tier-2-Data-Sheet-TB-11-6115-741-24
and this TM: https://www.steelsoldiers.com/showthread.php?165569-Tier-2-Data-Sheet-TB-11-6115-741-24
Last edited:
maniatopoulosg
Member
- 116
- 8
- 18
- Location
- Miami, FL
Bluejoe
New member
- 12
- 5
- 3
- Location
- New Jersey
Hello How did you make out with this unit. Any resets How many hours and how is it running? Thanks Joe
Jigawatts
New member
- 18
- 9
- 3
- Location
- OBX, North Carolina
The unit does NOT have any “resets”, it currently has 7 hrs and thanks to “klopk” I have finished the MOV mod! It had the fuse mod but no MOV. The unit has been running fine (after a careful and detailed inspection and initial precautionary maintenance) with the peace of mind of having the MOV in! Thanks to all the members here, I have been busy going through the machine and it’s a long story,.... which I do plan to post for those who care to read in a new thread! I’ll post a link here when I can finally finish the last few items on my list and put it all together so that hopefully it too may help others as I have been helped!!