- 265
- 4
- 18
- Location
- Hershey, PA
Does the passenger seat back assembly "hook" at the top and fasten with two bolts at the bottom? I need to remove it from the cab for the media blasting and can't see back there.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Passenger Seat Back Removal
- Thread starter rboltz
- Start date
foxtrk2
Member
- 153
- 4
- 18
- Location
- foxboro ma
as i remember removeing mine your thinking right
M-37Bruce
Active member
- 705
- 59
- 28
- Location
- Midlothian, VA
Two hooks, top & two bolts, bottom. I've got a pic somewhere?
1943ht
Active member
- 478
- 94
- 28
- Location
- Clermont Florida 34711
That's affirmative .. two 5/16 NF (24) bolts on the bottom ... just did my seat back yesterday regards those bolts .. ran a tap thru the holes to clean them up 
before installing.
before installing.
- 265
- 4
- 18
- Location
- Hershey, PA
Thanks
Thanks again to all. I still hope to have everything blasted and painted by summers end. Then, rewire and reassemble over the winter. My only dilema is the tail gate. It's bent several ways and I have no way to straighten it.
Thanks again to all. I still hope to have everything blasted and painted by summers end. Then, rewire and reassemble over the winter. My only dilema is the tail gate. It's bent several ways and I have no way to straighten it.
M-37Bruce
Active member
- 705
- 59
- 28
- Location
- Midlothian, VA
Post a pic, with all of the brain power here, we might be able to give you some advice/input on your tail-gate.
majorhitt
New member
- 227
- 0
- 0
- Location
- Dallas Pa.
Lost my brackets, fabbing new ones. Then when just about to install the new brackets and the originals showed up!! Yes just like everyone said two bolts on the bottom and drop in on the top.
- 1,229
- 53
- 48
- Location
- S.E. WI & S.E. TN, USA - Earth
Can someone post a picture of the top clips for the passenger seat? Mine don't exist and I will need to deal with that in a month or two.
Thanks,
Bert
Thanks,
Bert
M-37Bruce
Active member
- 705
- 59
- 28
- Location
- Midlothian, VA
I'll make an effort to get out in this heat and take a pic of mine, I will need to remove said cushion. I have one original and one house/home made.
M-37Bruce
Active member
- 705
- 59
- 28
- Location
- Midlothian, VA
Passenger Seat Pic's
101 degree's as I type!
The first one is stock, the other is one I made from a conduit clamp and self taping sheet metal screws.
At some point, I will go back and create a new one with all of my newly developed or re-discovered skills.
101 degree's as I type!
The first one is stock, the other is one I made from a conduit clamp and self taping sheet metal screws.
At some point, I will go back and create a new one with all of my newly developed or re-discovered skills.
Attachments
majorhitt
New member
- 227
- 0
- 0
- Location
- Dallas Pa.
I had the seats out of my M37cdn. You could see the 1/4' bar that goes from bracket to bracket on the top, the two humps are where the support brackets go. Then on the back of the cab I held a pointer at the bracket. I should have moved to the right to get both brackets in the picture. Hope this helps.
Attachments
- 1,229
- 53
- 48
- Location
- S.E. WI & S.E. TN, USA - Earth
Thanks for the pictures, I'll fab two in the next few weeks.
Bert
Bert
1943ht
Active member
- 478
- 94
- 28
- Location
- Clermont Florida 34711
"T-H" where are you located in WI? I'm in River Falls WI (MN Border)and am just finishing up my M37 Restoration .. My thread on the M37 Forum is "Another one Bites The Dust."
//R//
Mark
//R//
Mark
- 1,229
- 53
- 48
- Location
- S.E. WI & S.E. TN, USA - Earth
Mark,
I'm in Mount Pleasant. 6 hours S.E. of you. I also have seen your thread "Another one Bites The Dust" and have posted in it.
Bert
I'm in Mount Pleasant. 6 hours S.E. of you. I also have seen your thread "Another one Bites The Dust" and have posted in it.
Bert
- 1,229
- 53
- 48
- Location
- S.E. WI & S.E. TN, USA - Earth
I had a buddy stop by and give me a sample of the bracket (see picture), I will set up my brake press and fabricate some of these in the next couple of weeks.
Bert
Bert
Attachments
M-37Bruce
Active member
- 705
- 59
- 28
- Location
- Midlothian, VA
This looks tighter than the one I have, I guess the tighter, the closer to the back? If you making a few, I would like to purchase one if it's possible?
- 1,229
- 53
- 48
- Location
- S.E. WI & S.E. TN, USA - Earth
No problem Bruce, it will be a couple of weeks before I get to it. I have to make extras for the guy that lent me his bracket.
Bert
Bert
- 1,229
- 53
- 48
- Location
- S.E. WI & S.E. TN, USA - Earth
Rboltz,
Sorry for the thread highjack.
Sorry for the thread highjack.
- 265
- 4
- 18
- Location
- Hershey, PA
Not a problem here. We all learned a bit!