• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Turbo Questions

dbesade

New member
25
0
1
Location
Blachly, OR
Hello All-

Long time reader, first time poster. I have a 1968 Kaiser M35A2, and the Turbo is leaking badly around the v-band. I'm planning to send the Turbo off to a shop (J&H) to be rebuilt.. but I'm wondering what I should replace while I'm in there. This is the list I have so far:


  1. Turbo Mounting Gasket
  2. Silicone Connectors
  3. Slobber Tube Gasket
  4. Exhaust Gasket

Anything I should be prepared for when I take it off?

-David
Blachly, OR
 

Speedwoble

Well-known member
606
301
63
Location
New Holland, PA
I drilled and tapped a pipe thread plug for future EGT while the turbo was off. Then plugged the hole with a stainless steel plug. When I eventually got around to adding an EGT probe I didn’t have to worry about getting the chips out while drilling.
 

dbesade

New member
25
0
1
Location
Blachly, OR
I drilled and tapped a pipe thread plug for future EGT while the turbo was off. Then plugged the hole with a stainless steel plug. When I eventually got around to adding an EGT probe I didn’t have to worry about getting the chips out while drilling.
That is a great suggestion- though I don't plan to fiddle with the Fuel, so I wonder if I really need the EGT if I'm leaving everything "stock".

-Dave
 

gimpyrobb

dumpsterlandingfromorbit!
27,786
755
113
Location
Cincy Ohio
Yeah, Its good to know if your going to melt your motor. You never know what was done before it got to you.
 

dbesade

New member
25
0
1
Location
Blachly, OR
Bump

So-

I got the turbo off without too much trouble, but the rear turbo mounting studs (Front are Nut/Bolt) on the exhaust manifold snapped when trying to remove the locknuts. Does anyone know the part number for those, and if they are replaceable, or if I should replace the entire exhaust manifold (God... I hope not).

-Dave
 

cattlerepairman

Well-known member
Steel Soldiers Supporter
3,256
3,355
113
Location
NORTH (Canada)
Nah..the studs rust and then snap off. It is a bit of a pain with the manifold installed but basically you drill them out. If you can drill through what's left of the stud, leaving only a thin layer of stud behind, you have a chance to get the piece out without damaging the threads. If you have to go wild and damage the threads, just, re-tap the holes and screw new studs in. They are a standard part that most automotive places carry. You can also drill them out and replace with nut-bolt as in the front.

I also recommend speding the extra few bucks and getting copper nuts for the turbo (and exhaust manifold if you ever take it off). They do not seize.
 

M543A2

New member
Steel Soldiers Supporter
1,063
11
0
Location
Warsaw, Indiana
We religiously use anti-seize on every bolt or nut we install. Put it full length on every water manifold bolt, they get corroded in place in the aluminum manifold if you do not then the head twists off. It would be wise to pull the water manifold bolts one at a time and anti-seize them while you still can.
 

dbesade

New member
25
0
1
Location
Blachly, OR
We religiously use anti-seize on every bolt or nut we install. Put it full length on every water manifold bolt, they get corroded in place in the aluminum manifold if you do not then the head twists off. It would be wise to pull the water manifold bolts one at a time and anti-seize them while you still can.
Oh yeah, when I was replacing the coolant hoses I ran into that. I replaced with Stainless hardware and used anti-seize on them. I ended up having to replace one of the 2 manifolds. Every bit of maintenance on this rig ends up being 3 things to complete one thing :).. (Like replacing the Water Manifold and hardware to replace the coolant hoses :D)

So I have a local shop here in Oregon (Oregon Fuel Injection) that is a Borg-Warner shop and is familiar with the 3LM series (D Turbo's). Happy to pass along their info to anyone in the PNW if its needed. I'm looking at having to pull the exhaust manifold and likely replacing the hardware while I'm there.... at least I can do the work inside.

-Dave

-Dave
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks