Ford Mechanic
Active member
- 1,805
- 7
- 38
- Location
- Edenton, NC
Yeah, I turned around and he was sitting on the top step of that ladder. He's good about using the ladder to get in the bed of the truck too if I'm working on something back there.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your 5 ton this week?
- Thread starter dezert ratt
- Start date
Another Ahab
Well-known member
- 18,007
- 4,579
- 113
- Location
- Alexandria, VA
- 3,871
- 497
- 83
- Location
- Gray Court SC
That's why you buy a backhoe. 
gottaluvit
Well-known member
- 1,786
- 29
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Or a 5 ton dump.
Ford Mechanic
Active member
- 1,805
- 7
- 38
- Location
- Edenton, NC
The wife keeps telling me it's "exercise"Me, too.
From over here, that sure looks like a lot of work.opcorn:
Spyderman
Active member
- 393
- 37
- 28
- Location
- Alexandria KY
big block 88
Member
- 862
- 17
- 18
- Location
- Topeka/Kansas
Been doing my least favorite thing.... Soldiering and routing/fastening all the wires for the front and rear camera and front and rear lights. I hate wiring
Jeep Nasty
Active member
- 379
- 244
- 43
- Location
- NH
Got my new license plates for my truck now that he qualifies as an antique.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Another Ahab
Well-known member
- 18,007
- 4,579
- 113
- Location
- Alexandria, VA
- 18,551
- 5,926
- 113
The way that's spelled, I could almost hear President Johnson (aka: LBJ) speaking the name of this great nation with his deep Texas drawl.Got my new license plates for my truck now that he qualifies as an antique.
Sent from my iPhone using Tapatalk
Now that you mention it, I agree that New Hampshuh is indeed a State in Murica.
ROFLMBO
Carry on.
gottaluvit
Well-known member
- 1,786
- 29
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Pressure washed mine and my M105A2 today getting it prettied up for the Findlay Armed Forces Weekend. Now if we get another dry day, I will do some rattle can touch up.
Spyderman
Active member
- 393
- 37
- 28
- Location
- Alexandria KY
Finally got my hitch put on.
I wanted it up nice and close so I didn't hurt my departure angle.
Believe it or not the drop hitch is from my 85 Chevy Blazer.
All the info about the hitch because I know people are going to ask.
Still a good height for my trailer.
Plenty of clearance.
I wanted it up nice and close so I didn't hurt my departure angle.
Believe it or not the drop hitch is from my 85 Chevy Blazer.
All the info about the hitch because I know people are going to ask.
Still a good height for my trailer.
Plenty of clearance.
gottaluvit
Well-known member
- 1,786
- 29
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
What trailer are you pulling? A civy unit? Nice hitch. You painting it O.D.?
Spyderman
Active member
- 393
- 37
- 28
- Location
- Alexandria KY
Yeah I have a civi trailer that I need to pull sometimes. I just got rid of my Toyota Tundra. So my 5 ton is my only truck now. I will paint it to match soon.
Sent from my mobile web slinger!
Been a busy week for me....Tuesday I masked off my truck after work, Wednesday got the first coat done and since today (Friday) is my day off I finished painting the spots that I needed to do from the day earlier and got the second coat on.... Yes Coffey the chrome round mirror is now painted green as well! lol
Then I went and put my LED rear stop/turn lights in. Still need to swap out the fronts but I need to look up what folks are doing to get the front "park" lights to also be on when in Service Drive. and then I'll work on doing them another day as I will need to paint the front's green as they are Tan (forgot that they were)...
To see more pics visit my dedicated thread for my trucks.
http://www.steelsoldiers.com/showth...w-s-recovery-and-building-of-The-Beast/page15
Then I went and put my LED rear stop/turn lights in. Still need to swap out the fronts but I need to look up what folks are doing to get the front "park" lights to also be on when in Service Drive. and then I'll work on doing them another day as I will need to paint the front's green as they are Tan (forgot that they were)...
To see more pics visit my dedicated thread for my trucks.
http://www.steelsoldiers.com/showth...w-s-recovery-and-building-of-The-Beast/page15
Smokinyoda
Member
- 657
- 8
- 18
- Location
- Franklin, NC
Looking Good! What I did for the park lights was disconnect the wire that feeds the front park light and feed it instead with a jumper from the side clearance light (circled in red). That way it still works with just park lights on, and also with headlights on. Sorry but don't remember off hand the wire numbers. Super easy to do with no diode needed or jumper wire at the switch.
Attachments
Cinman37
Member
- 61
- 0
- 6
- Location
- Pittsburgh, PA
I bypassed the t-case air interlock cylinder and bypassed the air switch on the front of the t-case that engages the front axle while shifting into low range. I degreaser the under carriage, pressure washed the entire truck and installed the cargo cover. I just have to grease it before I take it to the National pike Steam show next Saturday.
Attachments
Cape Coastie
CWO4 ENG/MSS, USCG, RET.
- 528
- 124
- 43
- Location
- Sandwich, MA
Getting stuff done
Finally got around to doing stuff I have had parts for but not the time to install. Installed the new air dryer and PPV valve. The new dryer has to have new holes drilled to mount and 2 of the 3 bolts to install are too long for the mounting plate and allow the dryer to tighten up. Just added a couple of extra lock washers as spacers and it fit and tightened fine. Also painted both to add a little extra protection. It looks a little dirty under the truck due to some grease slinging from the u-joints. Cleaning planned soon. Also removed the cargo cover to repair a few holes and add new rubber rope. Have other parts to install and will work on the as time allows.
Finally got around to doing stuff I have had parts for but not the time to install. Installed the new air dryer and PPV valve. The new dryer has to have new holes drilled to mount and 2 of the 3 bolts to install are too long for the mounting plate and allow the dryer to tighten up. Just added a couple of extra lock washers as spacers and it fit and tightened fine. Also painted both to add a little extra protection. It looks a little dirty under the truck due to some grease slinging from the u-joints. Cleaning planned soon. Also removed the cargo cover to repair a few holes and add new rubber rope. Have other parts to install and will work on the as time allows.
Attachments
gottaluvit
Well-known member
- 1,786
- 29
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Truck looks nice. Is that a two-tone tan camo paint job?I bypassed the t-case air interlock cylinder and bypassed the air switch on the front of the t-case that engages the front axle while shifting into low range. I degreaser the under carriage, pressure washed the entire truck and installed the cargo cover. I just have to grease it before I take it to the National pike Steam show next Saturday.