- 7,017
- 9,695
- 113
- Location
- Papalote, TX
I don't think that is a smart start box, IIRC that is a really old box, its days were numbered.
Last edited:
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your HMMWV today/lately
- Thread starter Warthog
- Start date
As usual, you are correct Mog. I opened it up and there are numerous contacts inside burnt and melted. Also with a date code of 2002, truck is a 2001.
- 3,596
- 3,518
- 113
- Location
- Brooklyn, NY
Everything you ever want to know about rebuilding your PCB EESS to bulletproof.
How to bypass PCB? I am aware some HMMWV owners have done it. TOBASH
I'm not trying to speak sacrilege here, and I don't want to precipitate a war of words. :shock: How might I build a manual control box? My 24Volt Landcruiser just uses a glow wire to show glow plugs are ready, and then she just starts right up with the twist of a key. Civilian 6.2 Diesel...
www.steelsoldiers.com
EDIT- The SSI solid state box sucks. And it is almost impossible to trace the failure points. Just rebuild or replace. IMHO
Last edited:
- 4,414
- 4,207
- 113
- Location
- Brentwood, Calif
The reason TACOM continued to put out contracts for different PCB’s and EESS’s was because they couldn’t keep the failure rates down to
an acceptable level, it wasn’t till the S3 development that they finally developed a box with an acceptable level of MTF.
The box you have was of limited release, it was one of two “single component“ boxes developed, these single component boxes, “SSI and KDS green label” were quite problematic. Its still common to get surplus trucks that have the very first box made “PCB” all the way up to a new S3, and every other type box in between.
an acceptable level, it wasn’t till the S3 development that they finally developed a box with an acceptable level of MTF.
The box you have was of limited release, it was one of two “single component“ boxes developed, these single component boxes, “SSI and KDS green label” were quite problematic. Its still common to get surplus trucks that have the very first box made “PCB” all the way up to a new S3, and every other type box in between.
thompsoncustom
Active member
- 136
- 106
- 43
- Location
- iowa
That board doesn't look to be burned all that bad I wonder if you could just rebuild it for a couple bucks.
- 29
- 69
- 12
- Location
- Camden, DE
No pictures to add but stoked to announce I got my 1123 inspected and registered yesterday! Although it seemed every person I had to deal with had no clue what to do with a MV it went relatively easy. Best 2 1/2 hrs I've ever spent at the DMV.
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Installed horse stall mats from tractor supply. I opted to remove all of the plywood, including underneath the rear AC unit. Thats when I realized that unit has "feet" all around it and there are corresponding holes in the plywood. There are also refrigerant tubes that go straight down through the floor.
I laid the old plywood on the rubber mats to use as a template, and drilled holes to match.
I also made floor mats with the remaining cutoffs from doing the tunnel.
I'm pretty happy with the results.
I laid the old plywood on the rubber mats to use as a template, and drilled holes to match.
I also made floor mats with the remaining cutoffs from doing the tunnel.
I'm pretty happy with the results.
- 503
- 716
- 93
- Location
- Fort Lauderdale, Florida USA
On my last trip a couple of weeks ago, one of the AC hoses burned out with the exhaust and blew a hole. I took advantage of it to relocate the Red Dot AC condenser that was taking all my bed space. I am making all the lines new as the original ones are all cracked.
Attachments
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Got a broken rhino tire carrier from beltfed, now the fun part of fixing it!
- 7,017
- 9,695
- 113
- Location
- Papalote, TX
He does a pretty good job of getting difficult to ship stuff to you in one piece, he shipped me a set of supplemental armor doors that came in without any more scratches than they already had! looks like Fastenal!!
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Yep, fastenal. And always a good experience dealing with Austin!
- 3,596
- 3,518
- 113
- Location
- Brooklyn, NY
Austin is solid.
Gastrap
Active member
- 328
- 158
- 43
- Location
- Central Iowa
I got my rhino from him a few weeks ago and it was an easy fix. Installed it recently and just finished aligning the rear end to get rid of the extreme camber. It's amazing how much smoother the truck rides with a couple hundred pounds hanging out behind the bumper!
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Good to know, I was actually wondering about that. I just finished installing almost 200 pounds of rubber mats, plus the turret parts and now the rear tire carrier. I figure every pound will help the ride quality!
Gastrap
Active member
- 328
- 158
- 43
- Location
- Central Iowa
Definitely! My plain old 1097R1 with a soft top didn't ride bad with 30 PSI TP in the MT's, but the rear seat backs would bang around even on rough pavement before I put the rhino on. Pretty smooth now and way better on gravel washboards.
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Austin Aviation/HMMWV Surplus, aka Beltfed34 on ebay
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
My youngest son helping sort out the rhino tire carrier
By the way I realize I need new floors and a new kitchen, but I got my priorities straight. Humvee parts come first.
By the way I realize I need new floors and a new kitchen, but I got my priorities straight. Humvee parts come first.
- 1,331
- 594
- 113
- Location
- Quantico VA
You must have a very understanding wife. (She got a sister?) Don't forget to skim a few $$ every coupe of big purchases for flowers, lots of flowers...