1943ht
Active member
- 478
- 94
- 28
- Location
- Clermont Florida 34711
Noticed that these studs are for aluminum wheels ...did you happen by chance to resource a number for steel wheel applications?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Wheel Studs "Singling it Out"
- Thread starter 1943ht
- Start date
ke5eua
Well-known member
- 2,568
- 41
- 48
- Location
- Baton Rouge (Central), LA
They are in the pictures. I'll pull the specs though.
ke5eua
Well-known member
- 2,568
- 41
- 48
- Location
- Baton Rouge (Central), LA
No but I would imagine they would work for both applications.
1943ht
Active member
- 478
- 94
- 28
- Location
- Clermont Florida 34711
K5, disregard my request fo length on the Napa studs ... saw the pics from your previous post ... gettin old is h@ll
- 5,635
- 2,953
- 113
- Location
- Metairie/La (N'awlins)
The stud description is for Aluminum wheels as they are thicker typically than Steel wheels. There is no difference in the stud itself except for overall length and longer thread reach. The knurl and taper will be the same.
ke5eua
Well-known member
- 2,568
- 41
- 48
- Location
- Baton Rouge (Central), LA
That was the biggest requirement was for the knurl to be the same. The serrations are actually a little longer but the knurl is the same.
ke5eua
Well-known member
- 2,568
- 41
- 48
- Location
- Baton Rouge (Central), LA
New studs came in. Total cost was 340, that includes freight. Not bad I think.
This picture show all three studs for comparison. In the back are the new studs, one on left is original, and the right is the napa ordered one.
This picture show all three studs for comparison. In the back are the new studs, one on left is original, and the right is the napa ordered one.
goldneagle
Well-known member
- 4,537
- 1,066
- 113
- Location
- Slidell, LA
The question still remains are they long enough to properly hold the aluminum rims?
ke5eua
Well-known member
- 2,568
- 41
- 48
- Location
- Baton Rouge (Central), LA
I'll put the hub and drum assembly together today and give it a go.
ke5eua
Well-known member
- 2,568
- 41
- 48
- Location
- Baton Rouge (Central), LA
I have faith in these though. The stock studs would come right to the edge of the rim. With these being an inch longer they should give me enough to grab onto.
ke5eua
Well-known member
- 2,568
- 41
- 48
- Location
- Baton Rouge (Central), LA
Ok so I was pulling the studs in using the stock rim and the threads would stop before the stud was seated so I put the mrap wheel on.
Let me tell you, it was a PITA!
Studs are perfect, but I think I will have another issue to work with. The lug nuts are wanting to cut into the wheel so I think I am going to need to source the mrap lug nuts. Problem #2 is mrap lug nuts are M22x1.5 where the 900 / 800 / 35 series is 3/4-16.
Let me tell you, it was a PITA!
Studs are perfect, but I think I will have another issue to work with. The lug nuts are wanting to cut into the wheel so I think I am going to need to source the mrap lug nuts. Problem #2 is mrap lug nuts are M22x1.5 where the 900 / 800 / 35 series is 3/4-16.