draymorris
Member
- 38
- 22
- 8
- Location
- SW of DFW, The Great State of Texas
did not see one in the manuals forums. Any body have any?
Thanks
Thanks
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
wiring diagram for MEP-807A
- Thread starter draymorris
- Start date
- 2,145
- 3,526
- 113
- Location
- Pepperell, Massachusetts
There are some available at: http://www.liberatedmanuals.com/search.mpl?q=MEP-807a+generator&Search=Search
TM-9-6115-729-10
TM-9-6115-729-24
TM-9-6115-729-24P
Schematic is in -24 starting on PDF page 943
TM-9-6115-729-10
TM-9-6115-729-24
TM-9-6115-729-24P
Schematic is in -24 starting on PDF page 943
Last edited:
- 16,777
- 24,105
- 113
- Location
- Burgkunstadt, Germany
The manuals in liberated manuals are way out of date. I will post the newest version ASAP.
- 16,777
- 24,105
- 113
- Location
- Burgkunstadt, Germany
I am having problems uploading the manuals. The old ones in Lib manuals are way out of date. But below should be the schematics and a failure code listing for the MEP-807A. I will see what can be done about the manuals. They are huge.
View attachment 100KW Schematics and FAULT CODES 0116-1912_G_06-19-06[1].pdf
View attachment 100KW Schematics and FAULT CODES 0116-1912_G_06-19-06[1].pdf
draymorris
Member
- 38
- 22
- 8
- Location
- SW of DFW, The Great State of Texas
going to work on them tomorrow. Let you know how it goes.
- 16,777
- 24,105
- 113
- Location
- Burgkunstadt, Germany
The manuals are huge. Haven't given up. The-24 is 910 pages. It have tried reducing and splitting books, but still too big.
draymorris
Member
- 38
- 22
- 8
- Location
- SW of DFW, The Great State of Texas
I flashed the exciter with 12V - voltage on came up then the engine shut down. AL 8 ... on the screen. According to the TM 9-6115-729- 24 I have a lot of testing to do. Any input is appreciated.
- 16,777
- 24,105
- 113
- Location
- Burgkunstadt, Germany
If you are getting AL8, did you measure the voltage? Hook the meter to the 120 volt outlet, and then watch what happens. You say voltage came up, but how far? It would be nice if your volt meter would record peak voltage. Then you would not even need to watch, just read it after it quits.
Is this set new to you?
Have you ever seen it run right?
Is this set new to you?
Have you ever seen it run right?
Last edited:
GordonB
New member
- 8
- 0
- 0
- Location
- Brillion, WI
Does anyone Know how to hook up the remote start/stop on a MEP-807a, Documentation is hard to fine
- 16,777
- 24,105
- 113
- Location
- Burgkunstadt, Germany
You would get a lot more help, if you started your own thread. This thread is long dormant, and no one is going to be looking at it much.
draymorris
Member
- 38
- 22
- 8
- Location
- SW of DFW, The Great State of Texas
I have not been monitoring this site and just relying on an email to notify me of responses - sorry, for some reason I have not been getting notifications until now. For the record, I found wires disconnected on the transformer on the lower left side in the enclosure. Thanks for the diagrams.