• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Injection pump replacement

tommyd

New member
26
0
1
Location
NY
Happy Easter all,
My pump is done. Should I replace anything else while its in the shop? Would it be a good time to replace injectors and glow plugs? Bought it with 22k and now has 47k. Lastly, where would be the best place to get parts?

Thanks in advance!
 

chevyCUCV

New member
598
3
0
Location
Massachusetts
Im planning on doing headgaskets, ip, injectors, and front main seal.
That way i will do one tear down and major repair, and hopefully be good for a while.
 

tommyd

New member
26
0
1
Location
NY
A local shop wants 800 to refurbish the pump. Not going to happen! Anyone have a good reliable source for one? I seen eBay has a few, but what one do I need for a 85 1009? I'm not nearly on the mechanical level as most here. Should have spent more time around the motor pool!

Semper fi,
Tommy
 

Recovry4x4

LLM/Member 785
Super Moderator
Steel Soldiers Supporter
34,014
1,813
113
Location
GA Mountains
The problem you may have is getting a pump that you purchase, installed. Kinda like buying a steak at the grocery store and taking it to Longhorns and having is cooked. If there is a problem with the pump, who pays the labor to remove it for service. If the installer breaks it, who pays to replace it? I'd think long and hard before having parts you buy, installed by others.
 

det rebel

New member
157
0
0
Location
east texas
the pumps do take a little mechanical skill to replace but it can be done by just about anyone price of pump = my local shop can do it from 400 to 600 for just the labor now for finding a pumpthat might be difficult unless there is a scrap yard that buys military trucks close by
 

antennaclimber

Moderator
Moderator
Steel Soldiers Supporter
1,348
882
113
Location
State College, PA

chevyCUCV

New member
598
3
0
Location
Massachusetts
I got two ip's off blown engine's i bought on craigslist.
They were both recent replacements and very clean compared to the one in my truck.
Spent 100 for one engine, and got all the other parts that were left on it too

Great way to save money and end up with lots of extra parts that many people still need.

By shop do you mean mechanic?? If so you are going to have to spend lots, if its in your shop it is just more time that you will have to put in.
 

tommyd

New member
26
0
1
Location
NY
The mechanic is excellent and has no problem with me buyin the parts. Just wanted to know if there is a specific part number for the one I have in the truck. I do not have the time or know who to fix it properly myself.
 

chevyCUCV

New member
598
3
0
Location
Massachusetts
The mechanic is excellent and has no problem with me buyin the parts. Just wanted to know if there is a specific part number for the one I have in the truck. I do not have the time or know who to fix it properly myself.
You certainly have the know how, if you can read the forums, you can read a manual.
Its all just nuts and bolts, at least thats what i tell myself.

Understand the time part though, especially if this is your only vehicle.
 

GPrez

Member
208
0
16
Location
Mt. Airy, MD
I too wrestled with where to buy one for my M1009. I did alot of research before buying. The pumps are made by Standyne so I looked for a Standyne authorized dealer. The ones on ebay are tempting because of the price, but the reviews on those guys are not so good. Look up the company name on the BBB website and you will see what I mean.

I went with Mid West Fuel Injection (dieselstore.com) and it has been 2-years now and no complaints. They are a little more expensive than some I found, but I think it was worth it.

Someone else mentioned Oregon Fuel Injection above and they were also on my list to try. The only reason I didn't try them was because MWFI was in closer proximity to me shipping wise.

You want to get the Heavy Duty Pump.
 

JohnnyReb

Member
513
13
18
Location
North Georgia Mtns.
ok. i have a question. i have an 86 M1009 that is not getting fuel for some reason. you can fill up her fuel filter and all and she will run but after that, she loses all power and will not run at all. would yall think this would result in a bad injector pump? or do yall think its just a clogged fuel tank??

thanks,
johnnyreb
 

truck1

Member
332
10
18
Location
San Anselmo,CA.
Try Santa Rosa Diesel. Authorized Standyne dealer and rebuild station.Around 600$ to rebuild your stock pump with 1 year warranty. They are located in Santa Rosa ,CA. Better than a Ebay unknown who built it pump.Been to their shop- very clean and all techs trained by Standyne. Good luck.They wanted 1100$ installed to do a 6.2 pump.
 

WARWAG

Active member
ok. i have a question. i have an 86 M1009 that is not getting fuel for some reason. you can fill up her fuel filter and all and she will run but after that, she loses all power and will not run at all. would yall think this would result in a bad injector pump? or do yall think its just a clogged fuel tank??

thanks,
johnnyreb


Sounds like a dirty fuel filter to me. Change it.
 

Warthog

Moderator
Super Moderator
Steel Soldiers Supporter
13,775
227
63
Location
OKC, OK
Not many items to check in a CUCV fuel system.

Starting from the back.

1 - filter sock in the tank
2 - lift pump on the engine
3 - fuel filter
4 - injector pump
5 - fuel cutoff on the IP
6 - fuse for the IP cutoff
7 - injectors
8 - rubber hoses along the way

The tech manuals do have a step-by-step troubleshooting for the fuel system.

First thing I would do is check the fuel delivery to the fuel filter to see if the lift pump is working.

You may be sucking air thru a bad rubber hose.
 
Last edited:

det rebel

New member
157
0
0
Location
east texas
best way i have found is pull the hose that comes form the fuel pump on the side of the block going to the fuel filter and spin the engine over and see if fuel sprays out of it and not just trickles or slowly runs out it should have a good solid stream
 

Warthog

Moderator
Super Moderator
Steel Soldiers Supporter
13,775
227
63
Location
OKC, OK
best way i have found is pull the hose that comes form the fuel pump on the side of the block going to the fuel filter and spin the engine over and see if fuel sprays out of it and not just trickles or slowly runs out it should have a good solid stream

From the TM 9-2320-289-20 manual page 2-40
 

Attachments

det rebel

New member
157
0
0
Location
east texas
i normally dont have the TM in my back pocked and i didnt even know what it said, i was just giving my experience working on trucks and equipment.
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks