scottladdy
Member
- 538
- 8
- 18
- Location
- CT
How much did that set you back?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M1009- from forgotten to restored, my story
- Thread starter jdknech
- Start date
jdknech
Active member
- 1,095
- 6
- 38
- Location
- Jeffersonville, Indiana
By the time you buy it, have it optioned out and shipped new it's $3000.. I got it 6mo old from someone who used it on a escort truck (oversized loads) for $500 with a few other federal signal LED lights thrown in.. So it was still expensive, but compared to new was cheap lol
jbingvtx
Member
- 529
- 2
- 18
- Location
- Meadow Bridge, WV
Hey JD, It's going to look good when you're done. I"m still plugging away at the M884. Looks a little different than it did at Haspin 2 years ago.
jdknech
Active member
- 1,095
- 6
- 38
- Location
- Jeffersonville, Indiana
NICE! Looks like it is coming along nicely! You going to be at haspin this year?
jdknech
Active member
- 1,095
- 6
- 38
- Location
- Jeffersonville, Indiana
Got some parts today 
jdknech
Active member
- 1,095
- 6
- 38
- Location
- Jeffersonville, Indiana
I got the floor pans in this week, they are goodmark brand, I got them threw rockauto.. We will see how much I get done tonight, but I feel like I have a good start.. First things first, I had to start a fire for some heat in the garage
jbingvtx
Member
- 529
- 2
- 18
- Location
- Meadow Bridge, WV
Looks like progress!
Drock
New member
- 1,020
- 12
- 0
- Location
- Eatonton GA
Yeah now the fun part begins. cleaning , then fitting of the panels. I recommend get about 10 of thesehttp://www.harborfreight.com/4-12-in-polycarbide-abrasive-wheel-60571.html.,... And ah gallon of this......http://www.homedepot.com/p/Klean-Strip-1-gal-Phosphoric-Prep-and-Etch-GKPA30220/100406369. ,.... And about 6 cans of this....http://www.summitracing.com/parts/sum-sp1105.
Drock
New member
- 1,020
- 12
- 0
- Location
- Eatonton GA
Here that first link didn't work.........http://www.harborfreight.com/4-12-in-polycarbide-abrasive-wheel-60571.html
KansasBobcat
Member
- 641
- 8
- 18
- Location
- San Antonio, TX
My
M1009 was pretty rust free except where the floor mats and jut backing held the moisture where seats were bolted in. I treated the rust with Eastwoods rust converter, primed and painted 383 green. I have decided to go with simple rubber mats in front that are easily removable if it leaks...they all do! That way I can dry it up and spot any new rust. Thought it would be real noisy without mats and insulation but not bad. Quieter than 998. I understand that many units removed the mats while in service. Why GM supplied them that way who knows...probably some bean counter person with no practical experience got into the act.
Last edited:
cucvrus
Well-known member
- 11,473
- 10,433
- 113
- Location
- Jonestown Pennsylvania
My opinion again. After the floor is all fixed and seam sealed get it sprayed with Line X. It does an excellent job at sealing and sound proofing and it don't matter what water leaks you have. It just dries up. I had most of mine sprayed in black and 1 in tan. The tan is nice and bright. Looks dirty faster but you just hose it out and scrub it with a brush. Had it sprayed down to the bottom of the rocker panels on a couple of them. Best deal and seems to stop the rust. Makes it solid and nice. That is my opinion.
Drock
New member
- 1,020
- 12
- 0
- Location
- Eatonton GA
Agree, mine was line X'ed when I got. It is VERY durable. However I drive mine on the highway for 4-6 hours a day. I will be installing the rubber floor mat with the sound deadener on the back.
cucvrus
Well-known member
- 11,473
- 10,433
- 113
- Location
- Jonestown Pennsylvania
I had mine sprayed all the way inside up to the roof line. I had the decals all taped off and the gate done inside and out to the ridge reinforcement. Made a world of difference. I did wheels once . Never again. They never looked clean. Hard to wash unless you used the pressure washer every time.
jdknech
Active member
- 1,095
- 6
- 38
- Location
- Jeffersonville, Indiana
Made some more progress last night
jdknech
Active member
- 1,095
- 6
- 38
- Location
- Jeffersonville, Indiana
My QC inspector was snooping around
(I hate cats, but this one has grown on me)
(I hate cats, but this one has grown on me)
cucvrus
Well-known member
- 11,473
- 10,433
- 113
- Location
- Jonestown Pennsylvania
Question. Don't they make that center part of the floor?
- 275
- 3
- 18
- Location
- pefferlaw ontario
great job, one more thing , drill the floor and plug weld to the floor's cross members, that will make it super strong with no vibration,
Drock
New member
- 1,020
- 12
- 0
- Location
- Eatonton GA
Just ah suggestion. Your going to want to coat the inside of that cross member with some rust preventative coating. And also it looks like you haven't drilled any holes in order to spot weld to that cross member. http://www.eastwood.com/internal-fr...ode=ga220010&gclid=CI-S_sTX3MICFcvm7AodTVYAeA This stuff comes with ah 24" tube so you can insert it inside frame. Once inside it sprays like a sprinkler converting all the rust and coating everything with paint.
paraclete comes
Member
- 360
- 4
- 18
- Location
- southern ca
Those floors are looking good. I'm planning on finishing mine asap, one more rocker panel to go and a rear panel. Keep up the good work. Line x is excellent on these once all cleaned up.
jdknech
Active member
- 1,095
- 6
- 38
- Location
- Jeffersonville, Indiana
I'm not sure if they do or not.. But after working with the floor pans, I feel a tad more confident in my sheet metal skills, so I am trying my hand at making my own.. This is the first time I've ever worked with sheet metal, and I've only (very) recently started using a mig welder (takes some getting used to) I'm used to a stick welder and doing heavy welding lol