- 2,645
- 2,127
- 113
- Location
- Sunman Indiana
I sold my old pickup truck and snow plow, now winter is here so... I'm finally going to get the 11'x42" Gledhill plow that I found on the Web mounted of my M925.![IMG_2993.jpg IMG_2993.jpg](https://www.steelsoldiers.com/data/attachments/449/449666-9144fac895e55dd2606a5694f6c41a6d.jpg)
![IMG_2995.jpg IMG_2995.jpg](https://www.steelsoldiers.com/data/attachments/449/449667-5876702bc712847f1daa31f7dc50f957.jpg)
I'm going to try and keep the plow as close to the truck as possible, but will interfere with my bumper end when angled, so I'm looking for another bumper (bent???) and lift points that I can cut the outboard portions off.
![IMG_3016.jpg IMG_3016.jpg](https://www.steelsoldiers.com/data/attachments/449/449668-7d6f2b876d18c17038b04818b5050510.jpg)
I built a simple A-frame with an old 8 inch, six ton snatch block pulley that I hope to use the trucks winch to raise and lower the plow.
![IMG_3024.jpg IMG_3024.jpg](https://www.steelsoldiers.com/data/attachments/449/449669-12e53922c8e7d6032c6f2c89ae17a0d7.jpg)
![IMG_3028.jpg IMG_3028.jpg](https://www.steelsoldiers.com/data/attachments/449/449670-2436dc352a040e18496f1defda2fc88a.jpg)
![IMG_3033.jpg IMG_3033.jpg](https://www.steelsoldiers.com/data/attachments/449/449671-84a1592302fab513f5d0f527b300798f.jpg)
I also have an old single circuit 24v hydraulic pump that I plan on using for my angle cylinder.![IMG_3046.jpg IMG_3046.jpg](https://www.steelsoldiers.com/data/attachments/449/449672-df6e822d0a1ade62fae1483ffa9f73ca.jpg)
![IMG_3048.jpg IMG_3048.jpg](https://www.steelsoldiers.com/data/attachments/449/449673-d05adfeb26456b381ea5e5a982b43710.jpg)
![IMG_2993.jpg IMG_2993.jpg](https://www.steelsoldiers.com/data/attachments/449/449666-9144fac895e55dd2606a5694f6c41a6d.jpg)
![IMG_2995.jpg IMG_2995.jpg](https://www.steelsoldiers.com/data/attachments/449/449667-5876702bc712847f1daa31f7dc50f957.jpg)
I'm going to try and keep the plow as close to the truck as possible, but will interfere with my bumper end when angled, so I'm looking for another bumper (bent???) and lift points that I can cut the outboard portions off.
![IMG_3016.jpg IMG_3016.jpg](https://www.steelsoldiers.com/data/attachments/449/449668-7d6f2b876d18c17038b04818b5050510.jpg)
I built a simple A-frame with an old 8 inch, six ton snatch block pulley that I hope to use the trucks winch to raise and lower the plow.
![IMG_3024.jpg IMG_3024.jpg](https://www.steelsoldiers.com/data/attachments/449/449669-12e53922c8e7d6032c6f2c89ae17a0d7.jpg)
![IMG_3028.jpg IMG_3028.jpg](https://www.steelsoldiers.com/data/attachments/449/449670-2436dc352a040e18496f1defda2fc88a.jpg)
![IMG_3033.jpg IMG_3033.jpg](https://www.steelsoldiers.com/data/attachments/449/449671-84a1592302fab513f5d0f527b300798f.jpg)
I also have an old single circuit 24v hydraulic pump that I plan on using for my angle cylinder.
![IMG_3046.jpg IMG_3046.jpg](https://www.steelsoldiers.com/data/attachments/449/449672-df6e822d0a1ade62fae1483ffa9f73ca.jpg)
![IMG_3048.jpg IMG_3048.jpg](https://www.steelsoldiers.com/data/attachments/449/449673-d05adfeb26456b381ea5e5a982b43710.jpg)