Had a random thought, what about an electric starter off of something like a riding lawnmotor to spin a ring gear. Since there wouldn't be much load and I doubt you would have it spinning for super long periods, over heating shouldn't be an issue and I'm guessing the gear ratio would probably be close to 2500 RPMs on the barrels. Also I believe it wouldn't be too hard to make it look correct either. Just a random thought.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M134 Minigun build.
- Thread starter General Mcgregor
- Start date
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
I had that exact thought, if you look at pictures of a minigun the motor looks just like a starter that you could find on just about any small engine. It's just a matter of finding one in the correct size with the desired voltage and speed.
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
Want to see where this goes. Subscribed.
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
Bringing back to life a very old thread.
This project has been shelved for over three years but this week I decided to dig up all the old drawings and give it another go. The former parts were tabled in favor of a new design that will be easier to assemble. With lots of patience (and the help of an amazing welder) I have nearly finished the barrel assembly. This thing (if I ever finish it) is going to be super heavy, primarily because it is now being built entirely from steel (with a few bits of aluminum and plastic). The section you see in the pics has 67 parts, most of which are not visible. As I mentioned before, feeder/delinker assembly is going to be a killer in terms of mocking up and cutting/milling parts.
Anyway, I might regret it but giving it another go.
Stay tuned!
This project has been shelved for over three years but this week I decided to dig up all the old drawings and give it another go. The former parts were tabled in favor of a new design that will be easier to assemble. With lots of patience (and the help of an amazing welder) I have nearly finished the barrel assembly. This thing (if I ever finish it) is going to be super heavy, primarily because it is now being built entirely from steel (with a few bits of aluminum and plastic). The section you see in the pics has 67 parts, most of which are not visible. As I mentioned before, feeder/delinker assembly is going to be a killer in terms of mocking up and cutting/milling parts.
Anyway, I might regret it but giving it another go.
Stay tuned!
Attachments
- 14,639
- 4,817
- 113
- Location
- Buchanan, GA
If you need something made up. I can help. I hold a FFL 07/SOT 02.
Maybe one day I'll have a real 134...
Sent from my HTC6545LVW using Tapatalk
Maybe one day I'll have a real 134...
Sent from my HTC6545LVW using Tapatalk
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
Pretty much finished the barrel assembly today, everything went together very nicely with a few exceptions. I am very pleased with how straight everything is and how it looks when it's spinning, very nicely balanced.
Each tube is an individual part, it is not continuous through the clamp plates. There are alignment studs on each plate that keep the barrels in the right spot. Everything is clamped together via a set of six 27" long through bolts that thread into 1/4"-20 nuts inserted near the ends of the barrels.
Each tube is an individual part, it is not continuous through the clamp plates. There are alignment studs on each plate that keep the barrels in the right spot. Everything is clamped together via a set of six 27" long through bolts that thread into 1/4"-20 nuts inserted near the ends of the barrels.
Attachments
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
That whole assembly looks like it might be stainless steel; is it?
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
Cold rolled steel and one piece is aluminum.
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
Blasted and ready for powder
Attachments
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
Coated! Barrel assembly done. This will probably be my last post for a while as I am entering the design phase of the body, drive and mount. It will also take a while to source the material.
Attachments
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
![[thumbzup]](https://www.steelsoldiers.com/images/smilies/icon_smile_thumzup.gif "Thumbs Up [thumbzup]"){kind=icon}
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
So I am seriously considering making this a gas sim fire replica. So far I have not been able to find a practical way of making a sim kit with the correct rate of fire, 1000 rounds per minute is as close as I can get.
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
Project should see some momentum this week, I've elected to go with 5" exhaust pipe for the body and I have sourced the drive motor as well. Next big hurtle is getting a length of 7.62 ammo feed chute ahead of building the feeder/delinker.
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
Scratch the simfire option, too complex and too complicated. Plus I cant find a system with the right rate of fire anyway. Currently working on a way to rig up a fire sound effect to my PA system.
Motor is on it's way, this thing will be powered right off the truck by a 350 watt 24v dc electric lawn mower motor, should rip! Still going back and forth over the configuration of the body (Classic GE Terminator style vs Garwood door gun).
Motor is on it's way, this thing will be powered right off the truck by a 350 watt 24v dc electric lawn mower motor, should rip! Still going back and forth over the configuration of the body (Classic GE Terminator style vs Garwood door gun).
Attachments
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
Yes I do!!Post pics of the choices, and we'll give you our votes (like you cared).
Here is the GARWOOD door gun version, no carrier frame. Both feeder and motor on LEFT side
Attachments
General Mcgregor
Member
- 980
- 24
- 18
- Location
- Dover, New Hampshire
And the GE (T2 Predator) version.
