-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your MTVR today?
- Thread starter Elijah95
- Start date
- 3,871
- 497
- 83
- Location
- Gray Court SC
The wrecker will still be there for ya. Lol
Believe me, I’ll certainly need it! I’ll just be happy to push down trees bigger than my thumb again without bending my bumper. Whatever engineer thought an aluminum bumper on a truck is acceptable should be fired
Sent from my iPhone using Tapatalk
- 3,871
- 497
- 83
- Location
- Gray Court SC
Yes I totally agree
- 284
- 234
- 43
- Location
- Herriman UTAH
MAdams,
Nice video and a great idea on how to attach a trailer receiver to the truck. I like that no mods were done to the truck! Are you going to be selling these trailer hitches?
Nice video and a great idea on how to attach a trailer receiver to the truck. I like that no mods were done to the truck! Are you going to be selling these trailer hitches?
Barowner
New member
- 8
- 0
- 1
- Location
- Hamilton mt
The bumpers are aluminum?
seriously?
seriously?
Can’t seem to catch a break lately with rain, but spent 4 hours today doing a final test fit and tacking up the home made beveled C channel, followed by a single root pass and 2 caps to cover. Man a 30% duty cycle sucks at times; luckily the MEP802A powering my welder never complains and runs efficiently.
Going to break the tack on the top piece, do a little grinding and move it higher until flush w/bottom of side plate [ channel. Prime it, and throw a fresh coat of BEHR exterior house paint on it
Sent from my iPhone using Tapatalk
Going to break the tack on the top piece, do a little grinding and move it higher until flush w/bottom of side plate [ channel. Prime it, and throw a fresh coat of BEHR exterior house paint on it
Sent from my iPhone using Tapatalk
- 3,871
- 497
- 83
- Location
- Gray Court SC
Just make sure you get rid of that ugly damn tan lol.
MTVR
Well-known member
- 698
- 747
- 93
- Location
- Waco Texas
The OP (Elijah95) asked me to join this thread, so I'm here.
I'll be detailing the progress of my MTVR purchase in my introductory thread:
Mine is a 2007, indicating 3443 miles and 216 hours.
I just submitted my EUC this morning.
I'll be detailing the progress of my MTVR purchase in my introductory thread:
Our MTVR camper:
Greetings. We just purchased an MTVR from GP. The vehicle is a 2007, indicating 3,443 miles and 216 hours. I spent hours scouring the Inspection Reports and photos, and tried to pick the nicest one. The only material defect listed in the inspection report, is that the CTIS is flashing. I have an...
www.steelsoldiers.com
Mine is a 2007, indicating 3443 miles and 216 hours.
I just submitted my EUC this morning.
- 284
- 234
- 43
- Location
- Herriman UTAH
Good looking truck. 2007 - so you will have A/C built in. I see the rear ladder is missing. Maybe it is in the bed or the "trunk".
MTVR
Well-known member
- 698
- 747
- 93
- Location
- Waco Texas
The ladder appears to be missing. The wheel chocks are still inside the right-side steps, so I may find some fun stuff left behind under the passenger seats and/or in the troop seat stowage compartment.
We're not going to be using the tailgate or ladder, and we may not even be using the bed sides- mostly we just need the flatbed, (and quite possibly the ISO locks) to mount our overland expedition box.
MTVR
Well-known member
- 698
- 747
- 93
- Location
- Waco Texas
Elijah, I may be interested in that winch, but it's probably not gonna be until after I have been able to take delivery of my truck...
MTVR
Well-known member
- 698
- 747
- 93
- Location
- Waco Texas
I'll try to get with you once my truck arrives...
