Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
Hello, is there anybody’s out there that can help me find a electronic governor control for a MEP 804B any help would be greatly appreciated Thanks
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Electronic governor control for MEP 804B
- Thread starter Antonio Pena
- Start date
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
Hello out there, I replaced A5 with the instructions provided unfortunately I still don’t get any power I here the contact draw in but no out put. Can anybody help with what to check for?
- 2,145
- 3,526
- 113
- Location
- Pepperell, Massachusetts
Do you have a copy of TM 9-6115-643-24?
It has a troubleshooting section regarding no AC output.
It's in section 3.11 in my copy of the TM
It has a troubleshooting section regarding no AC output.
It's in section 3.11 in my copy of the TM
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
Thank you I’ll check it out!
- 16,765
- 24,069
- 113
- Location
- Burgkunstadt, Germany
Do you have voltage at the 120 volt outlet on the control panel?
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
No voltage at 120V outlet. I Installed a replacement A5 GCU with a schematic you provided for another thread and everything worked out per instructions. I bought an Ebay open box voltage regulator I’m not sure how to test it any help would be greatly appreciated Thank you!
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
- 16,765
- 24,069
- 113
- Location
- Burgkunstadt, Germany
The problem my not be in the A5. It might be in the A1, volt regulator, or someplace else. Do your volt and hertz meter move at all during start up?
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
No, the volt meter jumps a very little the frequency knob accelerates and and lowers engine speed.
- 16,765
- 24,069
- 113
- Location
- Burgkunstadt, Germany
Is there a Quad Circuit fuse installed in the set?
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
Hello Guyfang, I don’t see or know what a quad circuit fuse would be it’s got a duplex receptacle with a GFI circuit breaker.
- 16,765
- 24,069
- 113
- Location
- Burgkunstadt, Germany
The quad fuse mod is to protect the A1 volt regulator. It has a fuse in it to keep the A1 from over volting.
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
I’m dealing with an MEP 804 B the attachment is different?
Zed254
Well-known member
- 866
- 466
- 63
- Location
- S. Hampton Roads, VA
Look at Guy's document, page 5 of 7, for 804A.
- 16,765
- 24,069
- 113
- Location
- Burgkunstadt, Germany
I mis-spoke, or better said, mis-wrote, here. The fuse protects the Quad winding FROM being damaged by the A1 volt regulator. But if the fuse is blown, the A1 will not take over the function of producing voltage. The installation of this mod is the same, no mater what set its installed on. My intent here is to make sure that we take this step by step. If the fuse is there and blown, replace it. If the set works, good. If it blows again, you have a bad A1. If the fuse is not there, install one, and try starting again. See if it blows again. Or, if it is good, and no voltage is produced, then we need to see if the Quad circuit is damaged.
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
Good morning. When I installed A1 EBAY open box I installed the A1 fuse generator started although there was no power I checked the A1 fuse and it was good, I’ll go through schematic 5.2 troubleshooting to see if it’s a bad voltage regulator! I’ll keep you guys posted Thank You for the HELP! ps the word stator sounds ugly.
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida
Antonio Pena
Member
- 72
- 7
- 8
- Location
- Florida