HEMTT Wheels for Your Deuce are READY TO ROLL!

[donkdonk]

Updated price to $250 each painted in OD colors or flat black, $225 unpainted, and $300 in automotive base/clear paints.

If you have stock HEMTT wheels I will take them in on trade. I will also take 14.00, 14.50, 16.00, 395/85/20's on trade. I also need a tow bar.

I have some rims ready to go! The HEMTT centers were cut out with a water jet, very nice. Stock pressed centers were then welded in place. This gives a nice 6" offset so the 395's and 14.00's don't rub on your deuce. I had planned on just making these for my trucks, but I thought I would put them out there to see if there is an interest.

These wheels are new 2 piece tubeless HEMTT wheels that have been set up for a M35. Everything you need is included. All nuts to bolt the wheel together, the new O-Ring, and new correct valve stems (which a lot of people are not providing with their wheels because they are $18 each). These wheels are perfect for tire size 12.50, 14.50, 14.00, 16.00, 395/85/20, etc.

 

[donkdonk]

Here is a set I made for a friends truck.

 

[jesusgatos]

Centers cut out of stock deuce wheels? Looks good mang!

 

[donkdonk]

Centers cut out of stock deuce wheels? Looks good mang!

Yep. Thanks!

 

[jesusgatos]

What's the offset, and did you do anything to the centers (like cut holes) that will allow you to replace those studs if necessary?

 

[atankersdad]

Nice looking wheels. Ireally like the ones you made for your friends truck . Good work and very clean

 

[donkdonk]

Nice looking wheels. Ireally like the ones you made for your friends truck . Good work and very clean

Thanks!

 

[rideni]

be careful of the welds because you can get in trouble with DOT if the inspector is picky

 

[jesusgatos]

be careful of the welds because you can get in trouble with DOT if the inspector is picky

Are you talking about state inspectors?

 

[donkdonk]

be careful of the welds because you can get in trouble with DOT if the inspector is picky

Stock deuce rims are welded.

 

[wreckerman893]

Nice looking rims...great fab work.....would you take stock HEMMT rims in payment for 7 of the finished product?

 

[donkdonk]

Yes I would take them in on trade, but shipping might hurt it unless you have a cheap way to ship them.

 

[Seatyger]

Very clean and professional looking. Nicely done.

 

[SuperJoe]

very nice. i like the idea of the water jet as well. is there a pic of the back of the wheel at the welded part. i dont see why an inspector would frown

 

[donkdonk]

What's the offset, and did you do anything to the centers (like cut holes) that will allow you to replace those studs if necessary?

The center sits 3" (2 9/16") below the original flat wheel and the total offset is 6" (5 15/16). Is there a reason you would need to replace the studs other than if you somehow broke one? You could get most of the studs out if you needed to, but if somehow you broke one that is covered it would be no big deal to cut a hole so you could get it out.

 

[frodobaggins]

Who goes around having their rims inspected ?

"Hey man, while you're here, look at my rims and see if you can cite me please."

 

[frodobaggins]

Would you mind taking the front piece off and showing the work ?

 

[jblack6527]

Those look really nice!!!

 

[jesusgatos]

The center sits 3" (2 9/16") below the original flat wheel and the total offset is 6" (5 15/16). Is there a reason you would need to replace the studs other than if you somehow broke one? You could get most of the studs out if you needed to, but if somehow you broke one that is covered it would be no big deal to cut a hole so you could get it out.

Thanks. And yeah, that's what I was asking about (having to replace a damaged stud).

 

[donkdonk]

Would you mind taking the front piece off and showing the work ?

Not really much to see taking the front off, but here you go.