• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    There were 2 options, a 2 leaf reg duty and a 3 leaf hd for front, all same length. Rear spring sets had 2 lengths and came in 4,5,8 and 10 or 11 IIRC. Sent from my SM-G930T using Tapatalk
  2. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    http://www.truckspring.com/products/GM-Pickup-Replacement-Leaf-Spring-(3-Leaves-Front)__22-402.aspx http://www.rockauto.com/en/catalog/chevrolet,1986,k30+pickup,5.7l+350cid+v8,1053098,suspension,leaf+spring,7544 Positive arch unloaded is 1.125". Near flat installed, can't find measured...
  3. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Where did you find this? All the civilian stuff I know has the springs arched at 1-1/8" positive.
  4. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Where are the measurement points you're talking about doghead? I measured the ~3/4" between the bottom of the bumpstop and where it contacts the spring pack.
  5. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Hmmm...22" on drivers side, 22.5" passengers side center of hub to lower fender height. Less than 3/4" between spring and bumpstops. This about what everyone else has? I'm having trouble believing that is stock height unless these are supposed to be reverse arch springs from factory. Sent...
  6. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    I'll have to check my bushings out, I'm willing to bet they're shot. I'll also look for the spring eye damage while I'm under there. Didn't know the military wrap coming undone wasn't a big deal. Thanks. Sent from my SM-G930T using Tapatalk
  7. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Somewhat related question. From center of hanger to top of arch, who has the most out of shape springs? I'm gonna measure mine tomorrow but I'm thinking I'm at least 2" below. How far is considered too far? Sent from my SM-G930T using Tapatalk
  8. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    I don't mount, but the shop I used before I moved did all my mount and balance (I put on vehicle). They were good about cleaning and inspecting the rims and tires and would let me watch while they did it. Also the only shop East OTP Atlanta I found that could properly do the 4 wheel alignment...
  9. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Oh and my tires have never been mounted at a tire shop. I always do that myself! (That's why I have 4 trucks!) Sent from my SM-G930T using Tapatalk
  10. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Agreed on the jeep. I've got a '92 MJ that has to have near perfect balance to be road worthy because of the lift. My solution was 2 sets of wheels for it, one for driving and one to beat on wheeling. I wish I had room for a balancer, my lift, parts washer, blast cabinet, power coat oven, etc...
  11. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Completely shot would be bad enough to cause any wobble, IMO. Since they are a ball and socket fixture, they failure mode is usually gradual wear. I will of course check this (big prybar, watch for any play. Use a dial gauge if unsure). Perhaps I should mention again, that there are no...
  12. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    On my Fiero track car or my Mazdaspeed 3, I'd agree on the importance of balance. Those wheels undergo much more stress and turn much faster rpms. I'm more particular about my balancing and alignment in those vehicles because of that. In a truck that hardly sees 55, has no vibration at any...
  13. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Good call on the rotors, didn't think about that. I think I'll be doing those and shocks soon. Sent from my SM-G930T using Tapatalk
  14. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    The ends of the arches are 2-3" below the center of the arch. That about 5" difference from stock.... and the worst I've seen. Ball joints, etc are original and were in good shape when last checked up on the lift.... maybe 3000 miles ago. I believe one tie rod end was suspect and changed out...
  15. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Replaced springs when I did the bushings. One was broken, forgot about that until you mentioned it. If my tires were unbalanced, that would lead to a constant vibration at speed. I don't have that, the wobble only happens when braking or decelerating under engine load. Would be unusual for a...
  16. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Didn't put calipers to them, but the king pins looked to be in good shape when I did the bushings 2-3 years back. Truck has 43k on it. Shocks are most likely shot. Sent from my SM-G930T using Tapatalk
  17. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    Lift and crossover steering is the plan. K series Chevys are bad for cracking the frame around the gearbox. Ahaha, yeah they pretty much all look like that after a few (30+) hard years. Stock rear springs. Sent from my SM-G930T using Tapatalk
  18. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    I more meant the DS front hangar where the spring was coming unwound.... Sent from my SM-G930T using Tapatalk
  19. glaser06

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble"

    So, on a scale of "Meh" to "Dude, you're gonna die by death wobble" How bad are these springs? I've been putting off getting them resprung, death wobble is back after a 3 year hiatus. Replaced bushings in the D60 then (didn't look worn) and steering stabilizer (was worn). I suspect shocks are...
  20. glaser06

    Surging when off throttle

    Changed fuel filter today. Surging was real bad last night when I picked up the truck, very high idle upon first start. Cut the old filter open.... should have cleaned off the bandsaw but didn't. Looked pretty clean between the pleats, the trash on the cut surface was picked up by the blade or...
109,290members
164,274threads
2,311,768posts
548online users
Top