Search results

Used more Starting Fluid than I care to think about. When the rain comes and goes I'll jump on top and check the cam then pull the injectors. 15 minute job, right?

Hi Wes So I should hear the injectors clicking (firing) when the compress the diesel?

Thanks for the info!! Trying to decide if it's the injectors or pump. Don't think all the injectors could go south at the same time plus when I pinched off the return line I got smoke but no fire so I think the injectors are trying. I may end up popping the injectors out to see if crap got in...

The bypass (Probably wrong name) would be the one valve at the end of the hard return line from the head.

Hi...I checked the line before and after the fuel bypass valve. Tried at the head but couldn't get even the line wrench in there. So went downstream on the same steel line and disconnected at the bypass. Should be same result. I got a mild dribble out of there. This is baffling me but these...

Great video that I watched early on in December. Always good to know the basics. Just pinched the return line and it tried, no fire but could smell diesel smoke. Batts are low so will try tomorrow. It's a mystery to me as I find it hard that all injectors went bad from sitting. I did have the...

Hi..Sorry just saw the reply. For some reason SS isn't notifying me of reply's. Anyhow been screwing with this issue for a couple of weekends. I put a fuel pressure gauge on the pump above the solenoid and when hit with starter fluid it read 40 lbs. Fuel is flowing as I disconnected the fuel...

Thanks!!!!!

Hi..I was looking thru my old AC install post as I'm starting to put one of the M915 kits I have into my newly acquired pair of M923A2's. Your tips are great! I believe I bought the same Compressor brackets but were sold on EBay. Printed up your tension er mod. Have a great New Year (2019)!!!!!!!

I stand by my post.

Fixed the leak by pulling the cover and resealing with Permatex "The Right Stuff". Turns out one of the bolt holes is stripped. Will helicoil at a later date as it's holding up so far. Thanks for all the help!!

Time to call it quits tonight, tomorrow starts another work week. Thanks for the help! Will throw a pressure gauge on the pump next before diving into injector problems. Thanks Again!!!

Looking for the same info!

Yeah that's what I'm afraid of. Have a pile of cans laying around empty at this point.

Yes it has power to the solenoid, plus it's the same as when I pulled it of the other truck that ran fine. I'm freakin stumped. I'm going to run a continuous pressure on the tank and try starting that way. Should rule out air leaks even though when pressurized I see no leaks. So far 3 days of...

Hi...Went out and loosened that line and started with starter fluid. It wet the side of the motor, no soldier B to film. Went thru another can trying to start, no go. Could all 6 of the injector took a dump from sitting a year? Never heard of that but I'm stumped. The filter canister is full and...

Hi..Like your videos by the way. I used your PT pump install for reference! No I have the other pumps shutoff which is good. I just stepped back in after pulling the line on top and in turning over it bubbled up maybe 1" so diesel is getting to the line. Whats an easy way to check that its...

I also noted when I pulled the pump that the shaft on the air compressor rotated when starting.

I have a M923A0 that I used to haul water. Slowly last year it needed a bump in throttle to keep idling at lights. It slowly got worse then I parked it. This year I pulled the fuel filter which had crap in it. Cleaned it all up, new filter, new line from tank to injector pump but still wouldn't...

Thanks for the advice. This is the rear wheel but it's still a steering cap? So just unbolt, remove, clean and RTV? After a trip to Home Depo (20 miles) it leaks down the tire a bit. Found this YouTube video. https://www.youtube.com/watch?v=vJ0RgGWk1rU My question is when I remove the cap should...