Search results

TM 9-6115-642-10, Chap 3, Operator Troubleshooting Procedures

I have now lost three replies. Power keeps going out. Yes, followed chapter 3, troubleshooting guide. Looked through LP TM. Yes, I did fill the oil back to full. Did check coolant level, is good.

Nope, didn't notice any when I went to shut it down and don't see any when I turn s1 to prime/run.

Had a power outage last night. Turned 803A on, switched house power to genset power. It ran fine for 5 hours. Then there was a VERY short power fluctuation. Woke me up as my A/C unit beeped during the fluctuation. I went outside and the genset was running fine. No stuttering, nothing. I...

Well, I found a replacement pump on ereplacementparts dot com. $235 bucks. Part Number: 255-63103-10, Injection Pump AY. Manufacture is Subaru/Robin. Some other sites had it listed as low as $209. Still to much as far as I am concerned. Okay, so how do I rebuild this sucker. LOL. That...

Rustystud; Were you ever able to locate a replacement injector pump?

I just got a WDR1-270 3Kw generator with 200 hours on the unit. It will not start. I used the T.O. listed in this forum, 35c2-3-499-1, and followed the troubleshooting guide. No fuel is getting to the injector. The engine will start with a shot of starting fluid but will not keep running due...

I am still working on the rv. I have made some decent progress but no additional pics. I was Forced to do some landscaping projects by my wife. That did slow it down but didn't stop it. Honey-do's, gotta love them.

Csm, the mattress will stow vertically on the wall. It will slide down into a pocket and probably have a strap up top to help hold it vertical. Foam cushions will be used for the couch side of things. I want an actual 12 or 13 inch mattress as my bed in the rv. I took some pics of what I was...

Just as a note, Idaho did Not require a CDL for my rig. It is titled and registered as an truck/motor home. Because it is a cab and chassis style, it is considered a Class "C" motor home. Here, in Idaho. I have no idea about anywhere else. I am am working on the bed frame right now. I...

I didn't have the asbestos problem. I assume because I got this out of Minnesota, and the cold they have up there, that the heater was used often and therefore "fixed" at some point before I got it. There was no type of insulation in the bulkhead ducts or overhead ducts (the A/C duct had a...

I had thought about making the sides of the van slide in and out like normal RV slideouts. Because the walls flipouts are full length, it would be impossible to make a spot for a bathroom as the bathroom toilet needs to be stationary over the black water tank. It would also limit me in other...

I want to post a few pics and so forth of my build so far. I started a little while ago but as I am slow, I wanted to get a few areas done to start this. Here is the truck as I picked it up. Here is the van extended. I am taking out the ducting, lights and unnecessary wiring. The A/C...

Thanks, will PM.

I would like to have a winning bid item picked up at 3100 Creekside Parkway, Lockbourne, Ohio 43137 and then shipped via UPS to Bonners Ferry, Idaho 83805. I will provide exact destination address via PM if you would like to do this for me. The total weight of the two items is 60LBS, 30LBS...

I have a mobile MEP but I would have to pull it. I have a car trailer to pull with no extra room on it for the MEP. For the short term, the 400amp dual will have to work as my charger.

74M, I plan on boondocking often. That is the reason for the four 225mah batteries. I want to have plenty of battery storage and since I do not have a regular generator, I wanted a larger Alt to help out in the recharging area. An inverter with smart charge capability will be installed as...

You can also see the mirror reflection in ALL the windows. However, it is pretty cool looking. I don't see why it couldn't be done using a short wheel base vehicle.

I am converting my rig into a camper. I believe the amp break down, on the 400 amp alt, is 350amps at 28v and 50amps at 14 volts. It is a Niehoff and has the regulator with it. I have the cta8.3 Cummins engine with no extra goodies installed yet. It looks like it will fit, with maybe a few...

Oh, yes I can see how it may be confusing. In my head it was perfectly understandable. �� I am building a bed frame inside the van. I want to put the fresh water tank under the bed, inside the frame of the bed. There is much less chance of freezing with the tank inside the van...