Search results

That is why I started this post. I have seen at least 2 styles of rear fenders on CUCV's and thought it might have to do with who supplied the Kits and when. Some people may also be repairing their trucks with aftermarket or GM civilian fenders. Took a picture of the inside.

I don't know. I bought it from GSA. When you say stock GM dually, all of these were conversions from a kit as I understand it. I'm about as certain as I can be this is how the Air Force used it. I don't know what was in those kits. Typically these agency's out here spend nothing on the upkeep...

I brought the truck home, so I took a couple of pictures of the of the rear fender marker lights to show what I was talking about. I have seen others like these lights and I have seen others on Ebay and You tube that have the civilian style with the indentations in the fender that hold the...

I know that you will be in danger of being run over going 60mph but your fuel mileage will improve and so will the lifespan of the 6.2. Running it at 80 very long will not be good for it. Sometimes these CUCV's aren't used very much and the tires look good but check the dates on them to be sure...

RO(MAD).... I was tongue in cheek when I said cranky. It must have been a highly technical, complicated job. I'm leaning away from my M151 being one of these jeeps, except for that 64Kxx serial number that I haven't been able to disqualify.

I forgot about this thread. It is quite old. I wonder if he found the info he was looking for? I know a little more about them now.

Thanks for sharing that info. I looked at my M151a1 a little bit closer and I can't tell what the rating is on the generator and there are no holes in the dash where a plate may have been to identify the system. If I knew where the serial number location is I could see if it matches the plate...

I was looking at a few sites about M151 radio jeeps, (one of them that is good is linked to this thread) and some jeeps were plated with the specific radio system that was to be installed or plated after installation. Sounds like after? It just seems like... where would that system plate come...

I have heard that the serial # for the M151 is on the frame. I have done some looking, but can't find it. Is it visible? It looks like the AN/GRC 106 would be the easiest to install. I don't have a teletype. Would there be a dash plate making it a radio jeep with the 106 or 106a or could they...

Thanks from me also. Almost makes me want to take one out! That one fender bolt underneath typically gets rusted in badly. It has a captured nut that will break loose if forced. You don't want that, use plenty of penetrating oil.

I didn't consult a TM when I took off the front. It was quite awhile ago, and I don't remember alignment problems unless I was into fenders and doors. I just didn't have the means to lift anything very high. If you work on these trucks a lot you are going to have that ability, but if you are...

My truck is an a3. It did start out as a M1028. I'm the 1st civilian owner, but a University AG station had it after it's military service. They spent $zero on the truck so it is exactly like the AF left it. I'm reasonably sure it has the original marker lights on the fenders, but I was curious...

One thing I forgot to inquire about was how much you know about the history of your truck. Because while it's apart to that extent, it would be a good time to make sure the transmission doesn't need a rebuild, your radiator doesn't show any signs of a leak and the $900 engine is one you have...

You will need to remove the transmission 1st. It isn't that hard. Putting it back in is a pain sometimes. Take off the hood, unbolt the motor mounts. The hard part is lifting the motor, It is heavy and if you can't lift it over the radiator, There is quite a lot to remove to pull it out the...

I have always heard they were all conversions, but then ran across where a few 1986 made weren't conversions. It would be interesting to know when the conversions started. Like the date on that crate would be interesting. I'm interested to know when the decision was made that a dually was needed...

I have a M1028 dually but no data plate other than the original one. It was an Air Force truck, they must not have cared enough about the plate. I have seen pictures of many of these trucks and the rear fender reflectors and lights can look quite different. How how many years did they do these...

I sold one last week for I think, 2 or 250, it was rust free CUCV with glass but broken crank and 1 small ding

That page is what started all my questions. I found info that said Ford took over for Kaiser in 1965, then I found more info that Ford had a small contract in 1964 and at least some of the M151a1 had the 64Kxxx number as the frame number. I haven't found out yet where that number is on the...

I'm in a holding pattern. Summit has the Dorman on back order. With a projected ship date of 8/26.

There was a cab stiffener kit for the M66 ring. I think I would want that on there, if I had any ring up there, but I don't know the weight difference.