Search results

Delta Locks are available for anyone looking for a more redundancy on the Eco Hubs install.. Delta Locks are simple to install and lock the axle nut to the differential housing splines. The stock shims should be left in place. This spaces the delta lock correctly. The split lock is still used as...

Thanks for the feedback, I’m sure they could be available with out the logo. We are working out the details, pricing etc. Again thanks for the input.

Check out these. Replacement inner door lock knobs. They will be black anodised when finished.

Yes they are expensive! I did find some NOS for 500.00. Working on getting a good used one now.

Yes I’ve went thru everything from the sensor all the way to the front bulk head connector. All good no cross feeding and carried enough amperage to light a Lmtv headlight. With the resistance difference I’m leaning toward a sensor. Thanks

Thank you! I’ve checked the sensor and the resistance is way off compared to what it’s supposed to be and compared to my other truck. These things keep you busy!

I’m looking for a used or new speed sensor for the output of the transfer case. (Easy to access under the access plate on the rear of the transfer case) Does anyone have the part number. I looked in the TM and didn’t see it listed? Thanks.

Yes that was suspect also. I tested the harness all the way from the inside of the transfer case to the bulkhead connector. Not only resistance but made sure there was no cross connection between wires and made sure each wire would carry enough amperage to light a lmtv headlight.

We now have a good stock of door handle repair kits. A0 and A1. 70.00 shipped…. 2 strikers and 2 rivets in each kit. Repairs one left and one right Door. See the vendor section for more info .

This kit includes two strikers and two rivets to repair a left and right outside door handle. These strikers are built from 6061 billet aluminium and are reinforced in critical areas for extreme durability. Easy to install. Install these before yours break. They will! 70.00 shipped USA

I will look at them carefully. Checked for corrosion and breaks none found. Also checked to make sure there was no shorts to other wires in the bundle and that the wires could carry current. So far the wires look great.

Yes I pulled the speed sensor and measured it on the bench. It was 9.5 ohms. Measuring thru the pass thru on the second truck the speed sensor measured 271 ohms which is in range. My center diff solenoid also measures in the 3 ohm range.

My 2001 m1078 a1 speedometer stopped working and locked into a gear. Tested the speed sensor and got 9.5 ohms at 70 degrees. My 2004 truck tested 271 ohms. Looks like I need an output speed sensor. The one located inside the transfer case. Has anyone tested the solenoid for c7...

I got it figured out. I needed an app to open the tms and diagrams. Thanks

I tried to download and save from this site however after the download I can only view page 1. When I select a different page it goes back to page one ?? Thanks for your help. Mike

That would be great! I had mine in the shop today again. Checked the c7 coil and it seems to be very low impedance also. Checked voltage to the coil was a little over 26v idle in mode. Checked the top of the coil with a feeler gauge for magnetism, none. I didn’t have my scope at home but I...

Check out our new 6061 t6 replacement striker arms. They will be available very soon. Prototypes are done and tooling / programming is finished. The cost for a pair will be 70.00 shipped USA. Quantity discounts possible. Replace yours before they break! Or keep some spares on hand for...

Hi everyone, I’ve got another project finished up. Anyone interested in updating the striker arm in your door handles? Here are a couple photos of our new 6061 t6 arms.

I haven’t got back to that problem yet. From what I’ve read it looks like the c7 solenoid is powered 12 volt. Not duty cycled? I haven’t checked yet but will when it warms up a little. I now have a second truck and can swap parts if needed. Also should have a known good electrical to compare...

Hi Schmirgel, I don’t know if you know about Eco Hubs. They replace the 2:1 gear reduction units with direct drive. I’m going to be listing Eco Hubs for sale on a popular auction site . That site I’m told has very good rates on international shipping. The listing will be for one axle, so if...