Search results

Gentlemen, Thanks, very much, for your help. So, I pulled the magnetic pickup and although it looks fine, I'll test it per the TM today; 1-1.5V is what the manual states, but I'll be happy to see anything come out of it within reason. I've attached a few pictures for reference. There are three...

Nope, I haven't checked the magnetic pick up, but I'm going in to the TM now to find out what it is, where it is, and how to test it. Thank you! :)

Here's what I got from Guyfang that I'll check on now ...

Thanks, I'll keep that in my folder! I did start a new thread; again, thanks VERY much for your help. Joe

I did get advice from Guyfang (thank you!), and will go out to the generator right now to see what lights I get ...

Gents, I'm not getting power to the ADC100 electric actuator on my MEP-805b, so of course it won't start ... I've read through all of the similar threads that I can find, here and elsewhere on the IntraWebs. Just wondering if my genset problem is obvious to anyone out there. My MEP-805B cranks...

OK, I'm happy to start a new thread ... and I genuinely appreciate your help!!! Frankly, I was concerned about starting a new thread, because all too often I see members pounce on other members for not reading through the already posted threads related to their problem. This particular thread...

For the love of God, I've been away from this site for so long that I no longer remember how to post photos ... :)

MEP-805B Won't Start Here are a few relevant photos.

Gents, I have similar issues with my MEP-805b, and have read through the threads -- just wondering if my genset problem is obvious to anyone out there. My MEP-805B cranks, but wont' start. I have good fuel pressure all the way to the fuel shut off actuator on top of the injector pump. I did ran...

I'm looking to pay someone to pick up my DRASH trailer from Fort Bragg GovPlanet location and take it to a friends house in Cameron. Prefer pick up with a four wheel drive vehicle as it'll need to be towed to the back yard (about an acre lot); four wheel drive may not be necessary if it's dry...

Well, I bled each fuel filter and the strainer and had good flow with the pump engaged, so I pulled the fuel level sending unit and sure enough, the tank was empty, so I filled it with fuel, reinstalled the sending unit, and sure enough, it ran like a dream. I ran it for about 20 minutes, but...

That was REALLY helpful, thanks very, Very much. Turns out there IS a day tank; that plus the manuals and I'll give the generator another once over on Saturday to determine what's going on. Thanks again!

I've heard of this before, but can't find resolution in the manuals or searching this forum. My MEP-004A was running fine, but then just shut off and the low/no fuel warning light came on. I can start it and keep it running by (a) holding the the switch in the start position or by running it...

Kevin, Did you ever get any responses to this? I'm having the same problem with my MEP-004A and have read through the manuals and am thoroughly confused. First off, what's the "day tank" and where is it located? My genset ran fine until today, when it decided to shut down on it's own; once...

Thanks much, this was very helpful.

I have one pallet at Fort Riley that needs to be shrink wrapped before I can have it shipped; I'm happy to pay someone a reasonable fee to get this done. I need to get this done in the next several days; the alternative is if someone can pick the stuff up for me, wrap/crate it, then take it to...

Need help getting six pallets ready for LTL shipping. There are a total of six pallets containing 393 NHC 250 Cummins piston and liner kits that I would like to have (a) restacked, (b) consolidated into four or five pallets, and (c) shrink-wrapped extremely well so they will not move around...

Dave, Thanks for your reply! Actually, I found a transmission really close and got the shaft for nothing (it was junk), so were good! Any more NHC250 inframe kits available??? I'm still trying to get time to go through my mountain of parts ... :) Always a pleasure! Joe

Thanks for the replies! Do either of you know the NAPA or Fleetpride part number? It's at a truck repair facility, so I'm guessing that if the alignment tool has a commercial application that they'll have one in their tool bin, but if someone's got the part number that would really help...